查询词典 solution surface

We found, on the one hand, urea can cause cytochrome cboth on the electrode surface and in the solution to be denatured and then the denaturedprotein lends to move the formal potential of the native protein in the bulk solution to amore negative value; and on the other hand, urea can also cause the formal potential ofnative protein in the bulk solution to shift positively with decreasing the degrees ofdissociation of electrolytes and polarity of the urea-water solvent.

我们发现脲能引起电极表面和溶液中的细胞色素C的变性，变性蛋白质能导致本体溶液中天然蛋白质的标准式电位的负移；另一方面，通过降低电解质的离解度和脲-水溶剂的极性，脲能使本体溶液中天然蛋白质的标准式电位正移。

The effect degree order is: first, organic template; second, mineralization ion precursor; third, surface treatment; fourth, lay amount of thin film. In the process of biomimetic synthesis, first of all, the stone surface was pretreated with ethanol and functionalized with organic template solution, and then filmed repetitiously by using filtered CaC_2O_4 supersaturation solution as precursor.

仿生合成的影响因素的影响程度为：有机模板的影响＞成矿离子前驱液的影响＞石材表面预清洁方式的影响＞保护膜层数的影响，较佳的制备条件是：石材表面用乙醇预清洁，较浓浓度的有机模板溶液使之表面功能化，过滤的草酸钙过饱和溶液作前驱液，多层制膜。

In the process of corrosion in 3.5% NaCl solution, the ceric aluminum brass forms a homogeneous and tight corrosion film on the surface, which can inhibit the diffusion of Zn from the surface of matrix to the solution, and restrain the dezincification to a certain degree.

在NaCl (3.5%)溶液中腐蚀过程中，铈铝黄铜表面形成一层较均匀致密腐蚀产物膜，较好地阻止了Zn从基体表面向介质中扩散，在一定程度上抑制了脱锌；铈铝黄铜耐腐蚀性能略优于砷铝黄铜，腐蚀速率为6.2×10^(-3) mm/a。

After SBF solution cultivation for some days, the Ca/P coating was very easily deposited on the porous surface that was constituted of cystiform polygon made up with irregular nanometer circles like honeycomb. The energy spectrum showed that n/n atom ratio is about 1.61:1 which is very similar to that of HA and human bone. The active surface of the porous titanium after acid-alkali treatment and SBF solution condition which calcium-phosphorus ions was supersaturated induced the formation of Ca/P deposition layer.

SBF溶液培养后发现沉积层由蜂巢状多边形胞状物组成，这些胞状物是由网状纳米环无规则排列构成，能谱测定钙、磷元素原子比n／n约为1.61∶1，与HA和人骨中的钙磷原子比很接近；通过对沉积机理的分析，认为微孔钛的活性表面和SBF溶液过饱和离子浓度的环境造成了液相中钙磷盐的沉积。

It's found that th e activation of alloy was improved with increasing the concentration,temperature and immersing time of alkaline solution,the reason is that the Zr-rich surface of alloy was conversed to Nirich surface because of the strong erodent action of alkaline solution,this catalyzes ...

实验发现：储氢合金电极的活化性能随碱液浓度增大、温度升高以及浸泡时间的延长得到改善，主要由于KOH的强腐蚀性使合金表面由富Zr层转化为富Ni层，为氢的吸附离解起到催化作用，总结出最佳KOH处理液的实验参数：6mol/L、80℃、浸泡 2 4h ，在此条件下合金电极循环两周即达最大放电容量。

Degradation test in vitro was carried out in phosphate buffer solution (0.1M, pH7. 4) at 37 ℃. The buffer solution was changed daily. Degradation test in vivo was implanted the sample to subdermal in adult ICH rat in the scapular area lateral to the dorsal midline. At suitable time the samples were recovered. Molecular weight changes in surface layer and bulk of polymer sample were measured by GPC and weight loss was determined gravimetrically. It was found that the degradation behavior can be regulated by changing the composition of copolymers. The critical compositions from surface to bulk degradation behavior for PGCA, PLCA, PLMCA, PLDCA systems were 15-20, 20-30, 30- 40, 40 of mol percent GA or LA unit in copolymers, respectively. The degradation behavior of PGCA, PLCA, PLMCA, PLDCA systems were compared and analysed. Some factors influencing the degradation character, such as copolymer composition, hydrophobicity, crystallinity and enzyme affect etc. played important role.

体外实验中材料降解环境为37℃，0.1M，pH7.4磷酸缓冲溶液，每天换液，定期取样；体内实验中将聚合物试样埋置于ICH小白鼠背部肩胛骨皮下部位，定期处死小鼠，取样，将体内体外样品进行重量损失及试样内外层分子量变化测定，分析各聚合物试样降解行为特性，实验结果证明，改变共聚物组成，可以调节各聚合体系降解行为特性，对PGCA，PLCA，PLMCA，PLDCA共聚体系，交酯摩尔百分含量15-20％，20-30％，30-40％，40％分别为各体系内降解行为特性由表面降解型向本体降解型过渡的临界转折点，交酯含量较低的聚合物不同程度地表现表面降解行为特性，论文对各共聚体系体内外降解行为作了分析对照，例如共聚物组成对材料降解速度与降解行为的影响；生物体内酶对降解行为的影响；材料亲疏水性，聚合物链段结晶行为及碳酸酯结构对材料降解行为的影响等，得出交酯/环碳酸酯共聚体系降解行为一些共性和规律。

Through designing of composition and structure of the bioactive graded coating,innerstress and its distribution in the coating were analyzed and calculated, the resultsshowed that when composition distribution coefficient n was 1.5, a reasonable stressdistribution could be got, that was at the beginning of deposition the suspension containingrichly BG granules was used so that a rich BG granules layer, a good transitional layerbetween BG layer at the bottom and the coating could be obtained at the titanium alloy side,the bottom of the coating; the stress value near the interface and surface and its character,pressure stress or tensile stress, were decided by the character of its composition itself.Changing composition distribution coefficient n could only change the variation tendency ofstress in the coating, but did not change the stress distribution rule in the coating. Thethinner the coating is, the sharper stress variation in the coating is, which does not mean thatthicker coating is better because the thicker the coating is, the little the permitteddeformation of coating is, so the coating thickness should be thinner, for example, about50μm for bending applications, but for applications only bearing pure shear stress, such asroot of tooth implant, the coating can be thicker little, for instance, about 80～100μm. The study on electrification characteristic and electrophoresis deposition of HAand BG granules in aqueous and non-aqueous solution system found that EPD almost didn'toccur in aqueous solution system. However, because HA granules take position charges inabsolute alcohol, a homogeneous EPD be carried out on the cathode titanium alloy slice, but taking negative charge in absolute alcohol the BG granules not be deposited on the cathode. A guided HA crystallizing, 100～300nm, on surface of the BG granules be realized by metathetical reaction, which cover BG granules with HA microcrystals and make the covered BG granules taking position charges in absolute alcohol, sequentially realize the EPCD of the BG and HA granules on the cathode, so it is feasible to make a titanium alloy/BG/HA bioactive graded coating by making use of EPCD technology. The corrosion experiment of rich boron bioglass coating and plasma spray coating showed that split phase, rich boron and rich silicon phase, occurred during its preparation. In basic medium the corrosion behavior of 〓 BG coating showed uniformity corrosion, the corrosion mostly occurred at rich boron phase area, therefore batch formula design of BGshould avoid the occurring of split phase. The corrosion appearance of plasma spray coatingappeared a non-uniform corrosion, mostly occurred at the edge of the laminated HA moltendrops, and emerged an accelerated corrosion tendency, which will easyly lead to corrosioncrackles extending to the interface and the happening of osmotic interfacial corrosion, thatmay be one of the major reasons leading to the coating cracking-off in the later period. Thetesting results of thermal expansion coefficient of 〓 and 〓BG showed the thermalexpansion coefficient of 〓 BG matched with that of titanium alloy better, and 〓 BG couldsinter with titanium alloy into densification enamel layer at low temperature (720℃).

将Ti6Al4V合金在1000℃下进行真空热处理会降低其力学性能，且合金内的V元素会向表面富集，因此，钛合金真空热处理和表面涂层的烧结温度不能过高，即应低于其相转变点；通过对生物活性梯度涂层的组成和结构的设计，分析和计算了梯度涂层内的应力大小和分布，结果表明：对于本研究，当成分分布系数n=1.5时，可以获得较合理的涂层力学性能，即在沉积开始时，采用富含BG颗粒的悬浮液，以便在钛合金侧获得同底层BG有良好过渡的富BG涂层；梯度涂层界面和表面的应力大小、性质由材料组成本身的性质决定，改变成分分布系数，只能改变涂层内应力变化的趋势；涂层的厚薄不影响涂层内的应力分布规律，但涂层越薄，涂层内的应力变化越快，但这并不意味着涂层越厚越好，因为涂层越厚，涂层允许的变形越小，对于应用于弯曲受力部位的涂层而言，涂层应薄一点为好(50μm)；而对于仅纯受剪切应力的部位，如牙根种植体，涂层可适当加厚(80～100μm)；通过对HA和BG颗粒在水溶液体系和非水溶液体系中的带电特性和电泳沉积的研究发现，它们在水溶液体系中很难发生电沉积；在无水乙醇溶液中，HA颗粒带正电，可在阴极钛合金片上发生均匀的电泳沉积，而BG颗粒则带负电荷；利用复分解反应法，可以制得100～300nm的HA，通过诱导HA在BG颗粒表面结晶，可对BG颗粒进行表面包覆，获得了被HA包覆的BG颗粒，改变了BG颗粒表面的带电特性，使BG和HA颗粒在无水乙醇中均带上正电荷，从而实现了HA和BG颗粒在阴极上的共沉积。

Only when the fountain solution surface tension and ink are equal, the surface tension of the interface of diffusion pressure to zero, ink fountain solution and keep on the interface and to each other for invasion, Business card printing and membership card making effect is more desirable.

只有在润版液的暗地不抬力和油墨的暗地不抬力不等时，界面上的清除不抬为不整，润版液与油墨在界面上保留不绝对不均而互不浸润，制卡和会员卡制作成果才较为抱负。

On the other hand, if the surface tension of the fountain solution is less than the ink on the surface tension, the role of pressure in diffusion, the ink fountain solution to infiltrante in the direction of, so that printing dot disappears.

不正之，如果润版液的暗地不抬力小于油墨的暗地不抬力时，在清除不抬的功用下，润版液向油墨的标的目的浸润，使印品网点产生。

Treatment can be 1%-2% sodium bicarbonate solution, pre-cleaner mouth in the breast-feeding or nystatin (10 million units / ml) coated surface of the skin 3-4 times a day; or coated with 1% crystal violet solution surface of the skin 2-3 times a day.

治疗可以是1％-2％碳酸氢钠溶液，预清洗口哺乳或制霉菌素（1000万单位/毫升）涂在皮肤表面，每天3-4次，或用1％结晶紫溶液涂在皮肤表面，每日2-3次。

Pachomius manual labour was organized as an essential part of the monastic life; and since it is a principle of the monks as distinguished from the mendicants, that the body shall be self-supporting, external work of one sort or another has been an inevitable part of the life ever since.

根据圣pachomius体力劳动组织作为一个重要组成部分寺院生活；以来，这是一个原则的和尚，作为有别于乞丐，该机构应自支撑，对外工作的这种或那种已一个必然的一部分，生活至今。

In order to study the effects of parametrical rolling on the ship movement and tilts, in allusion to ship's navigating in regular following waves, the equation of ship rolling motion is transformed into normal Mathieu equation by proper variable replacement when strong parametrical excitation in restoring moment varied according to sine or cosine wave.

为研究参数横摇对船舶运动和倾覆的影响，通过对船在规则波上随浪航行时，恢复力矩中出现的1个以正余弦规律变化的强参数激励项进行适当的变量置换，将船舶的横摇运动方程转换成标准形式的Mathieu方程。