查询词典 sheet

The characteristic of this series leveler iS that it has adopted two national patent technologies:group driving plate levelling machine ZL200420001176.0 and axial decelerating motor leveler ZL200520007514.6.Each top roll is driven by a set of decelerating motor.and every two lower rolls are driven by a set of dynamic system,so that the line speed of each roll iS consistent with sheet metal speed of the contacting part,and it has solved the problems existing in traditional transmission system,such as friction between sheet metal and roll surface.and mechanical interference problem in the system And the working roll adopts spherical roller bearings which have little friction resistance.so this series leveler has such advantages as high levelIing quality,Iittle noise,low energy consumption and environmental protection.compared with traditional levelers.

该系列矫平机的特色之处在于：采用分组驱动板材矫正机(ZL200420001176.0)和一种轴装式减速电机矫平机(ZL200520007514.6)两种国家专利技术，每根上辊由一套减速电机驱动，每两根下辊由一套动力系统驱动，从而使各辊的线速度与所接触部位的板料速度相一致，消除了传统传动系统存在的板料与辊面之间的摩擦和传动系统内部的机械干涉问题，同时由于工作辊的轴承均采用轧机用调心辊子轴承，摩擦阻力小，因此，该系列矫平机与传统矫平机相比，矫平质量高、噪音小、能耗低、节能环保。

The results show that with the increase of strain rate, the grain sizes of thermal simulation AZ31B alloys with different deformation all decrease; however, when other conditions are the same, the higher deformation will lead to the formation of the smaller grain size, and as the cooling intensity decreases, typical cast structure of AZ31B will appear. With the decrease of roll casting temperature, the dendritic size of roll casting AZ31B alloy sheet prepared by the same strain rate is also reduced, but with the increase of strain rate, the dendritic size of the alloy sheet prepared by the same initial roll casting temperature is decreased, and the tendency of dendritic streamline is strengthened. During the roll casting process of AZ31B alloy, rolling force should not be large, otherwise it will cause heat cracking.

研究结果表明：在不同应变量下，热模拟样品的晶粒粒度均随应变速率的增加而减小，而当其他条件相同时，变形量越大晶粒粒度越小，冷却强度降低，合金呈典型铸态组织；利用铸轧技术生产的AZ31B合金，当应变速率一定时，随着初始铸轧温度的降低，铸轧态板材的树枝晶粒度逐渐减小；而在初始铸轧温度一定时，随着应变速率的增大，铸轧态合金板材的树枝晶粒度也逐渐减小；而随着应变速率的提高，树枝晶沿轧向呈流线状排列的趋势增强；在AZ31B合金铸轧过程中，轧制力不能太大，否则容易引起热裂。

An object of the present invention is to provide an apparatus for cutting a sheet-shaped material, which makes it possible to accurately cut the sheet-shaped material without the occurrence of cracks on the finished product side and burrs on the cutting surface of the finished product.

本发明提供了新的一种切割成型纸材料的设备，它可以做到精确切割成型纸材料而不会发生成品纸面上的裂纹和切割面上的粘胶。

SUMMARY OF THE INVENTION An object of the present invention is to provide an apparatus for cutting a sheet-shaped material, which makes it possible to accurately cut the sheet-shaped material without the occurrence of cracks on the finished product side and burrs on the cutting surface of the finished product.

本发明小结本发明提供了新的一种切割成型纸材料的设备，它可以做到精确切割成型纸材料而不会发生成品纸面上的裂纹和切割面上的粘胶。

Because aluminum surface unlike composite aluminum foil paper and aucilisty paper, it has a certain amount of micro-small holes, moisture penetration into the paper can be, so it is important for moisture control; and aim at aluminum sheet piling up cannot be printed matter is exhausted, the card with a maximum of 3000, because aluminum is not wear-resistant surface, piling up too much will crush India face about note aluminized paper storage time should not be too long, it is best not more than two months, for a long time will be subdivisionof with the back of the paper, the following is issued on picking flowers; by the aluminum sheet business card printing and membership card making bearing in mind that when you heat curing temperatures not too high, too high a temperature can affect aluminum surface which flowers, and too hot paper antishrinking rise on deformation is too big to post processing.

因为真空镀铝纸的暗地不像不简单铝箔纸和PET纸，它有必定的微洪不小孔，水不合可以不合泌出纸，所以不差水不合的把持不一不合重给；③真空镀铝纸的印品堆放不克不及太众，卡纸最众不超功3000张，因为真空镀铝纸的暗地不耐磨，堆放太众会压伤印背；④夺纲真空镀铝纸的不领取工夫不给太不幼，最好不给超功两个日，因为工夫不幼了暗地会跟纸的背后粘连，变成纸背发不攒；⑤真空镀铝纸的制卡和会员卡制息给夺纲冷固化时温量不给太矮，温量矮了会感化真空镀铝纸的暗地，使其变不攒，而且太冷纸张缩涨变形太不小，不差后增工感化很不小。

The closure of steel sheet piles is the key to the construction of steel sheet pile cut-off walls.

钢板桩合拢是钢板桩防渗墙施工的关键。

Structure computation of sheet-pile wall is a major part in design of sheet pile bulkhead, which is a main form of quay.

板桩码头是一种主要的码头结构形式，其中板桩墙结构计算又是板桩码头的一个重要内容。

A variety of them to overcome their difficulties, has successfully developed four kinds of different forms, with independent intellectual property rights of U-and Z-type steel sheet pile sheet pile, for a total of 14 varieties of different specifications.

他们克服多种困难，先后成功开发了4种不同形式的、具有自主知识产权的 U 型钢板桩和 Z 型钢板桩，共计14个品种规格。

This paper establishes a finite element model for the interaction between the soil and the sheet piles and performs a seismic response analysis for the portal water injection sheet pile adopting the nonlinear calculation module of finite element software ANSYS.

本文建立的有限元模型之间的互动，土壤和钣桩并进行地震反应分析，为门户注水板桩采用了非线性计算模块的有限元软件ansy

Through simulates between the mold and the sheet dynamic contact accurately, contacts the boundary dynamic change in the comprehensive analysis sheet and the mold in the foundation, unified the ANSYS software to give the model geometry description, the contact algorithm choice, the contact friction model establishment and so on the concrete method.

通过准确地模拟出模具与板料之间的动态接触，在全面分析板料与模具接触边界动态变化的基础上，结合ANSYS软件给出了模型的几何描述、接触算法选择、接触摩擦模型的建立等具体方法。

The system can be widely used in belt weighing and batching process control,etc.

介绍了基于智能模糊控制的嵌入式配料系统的设计方法，对模糊PID控制过程和系统调零作了重点的讨论，同时给出了PID控制的程序流程图和系统定长调零子程序。

"I dunno," she answered,"but if you show me aroun', I'll recognize it from the lighthouse just outside the porthole."

"我不知道，"她回答说，"如果你能带我转转，我能认出来的，因为灯塔就在舷窗外。"