查询词典 rust joint

It cuts both ways to work in a state-run enterprise or a joint venture: the pay from a state-run enterprise is relatively lower but you feel more stable while in a joint venture you feel unassured, through the pay is relatively higher.

在国营企业或合资企业工作各有利弊：在国营企业工作比较安定，但工资较少。在合资企业工作挣钱多一些，可是又不稳定。；

J7 d w It cuts both ways to work in a state-run enterprise or a joint venture: the pay from a state-run enterprise is relatively lower but you feel more stable while in a joint venture you feel unassured, through the pay is relatively higher..

8 ？4 '# Y# d Q！ r M， a 在国营企业或合资企业工作各有利弊：在国营企业工作比较安定，但工资较少。

It cuts both ways to work in a state-run enterprise or a joint venture: the pay from a state-run enterprise is relatively lower but you feel more stable while in a joint venture you feel unassured, though the pay is relatively higher.

各有利弊 cut both ways 在国营企业或合资企业工作各有利弊：在国营企业工作比较安定，但工资较少。在合资企业工作挣钱多一些，可是又不稳定。

O It cuts both ways to work in a state-run enterprise or a joint venture: the pay from a state-run enterprise is relatively lower but you feel more stable while in a joint venture you feel unassured, through the pay is relatively higher.

在国营企业或合资企业工作各有利弊：在国营企业工作比较安定，但工资较少。

It cuts both ways to work in a state-run enterprise or a joint venture: the pay from a state-run enterprise is relatively lower but you feel more stable while in a joint venture you feel unassured, through the pay is relatively higher.4 i1 W$ h2 w+ r- q1 e

H2 t% p 在国营企业或合资企业工作各有利弊：在国营企业工作比较安定，但工资较少。

The present paper introduces the modification of joint between adobe collector and drier ,pointing out that the adobe damaging caused by the height difference of joint can be avoided byadopting unfired tile lifter and the data obtained can be used for the similar equipment modification.

介绍了集坯器与干燥器接口改造，采用砖坯升降机解决接口高差带来的砖坯破损问题，可为类似设备改造提供参考。

The peel strength of HDPE/steel joint with the grafted HDPE used as hot melt adhesive is enhanced as compared with that joint with ungrafted HDPE powder.

随接枝率的增大，接枝HDPE与水的接触角下降，亲水性增加。

Through the stress calculation of a 3d jacket platform in wave, the change of load combination acting on the braces of multiplanar joints was observed, the influence of different load combination on the maximum stress and the location of hot spot was revealed, and the error in stress estimation caused by regarding multiplanar joint as uniplanar joint was analyzed, which shows the necessity of stress analysis to multiplanar joints.

本文通过一座波浪中的三维导管架平台结构的接头应力分析，考察了接头的载荷组合形式随波浪的变化，揭示了不同的载荷组合形式对接头最大应力及其热点位置的影响，分析了将空间接头作为平面接头来估算最大应力时引起的误差，从而说明了进行空间接头应力分析的必要性。

Slipper type universal coupling"s fork joint and palm end are the weak parts of the main transmission system. In this article, the two parts" intensity values are obtained through finite element analysis . After making three-dimensional computer simulation analysis by ANSYS, the results show that the middle arc of the fork joint in loaded side and the intersection of fork bore and the arc are the danger location, where the stress is largest and stress concentration is serious.

本文对轧机主传动系统机械部分的薄弱部件进行强度计算，即对滑块式万向联轴器的主要零部件的强度进行有限元分析，通过ANSYS有限元分析软件进行三维计算机仿真，由计算结果可知，在叉头受载侧过渡圆弧段中部、叉头镗孔与过渡圆弧交接处这两个部位的应力最大且存在严重的应力集中，考虑到单元总数限制及计算时间等因素，整体模型的网格划分较疏，不能反映倒圆角等细节。

The result shows the mistake choice of universal joint, the ways to solve the problem have been proposed, and it sums up experience of universal joint shaft made in china.

结果表明外方在万向轴选型上存在一定的问题，并针对选型偏小问题制定了解决方案，总结了该类万向接轴国产化的经验教训。

It's bell can reach over a meter in diameter.

它的身体最大可以达到直径1米多。

Now they are overdue and I shall have to pay a fine.

现在他们过期了，我不得不付罚款。