查询词典 quadrant plate

Using method: First clean the roller, then stick the open side of tesa printing plate mounting tape to the roller or sleeve, tear of the separating paper, and stick the plate to the tape. The initial adhesion is weak, suitable for repeatly tear off and stick on. The adhesion will be strengthen when the machine is running, which make the tight joint to plate.

使用方法：请先将印刷滚筒清洗干净，将tesa印刷专用贴版胶带展开面贴於印刷滚筒或套筒上，撕去离型纸，再将版材贴於胶带上。tesa印刷专用贴版胶带之初期黏著力较低，适合重复撕贴，如上机运转后，则黏度会增加，使版材能紧密接合。

Experiment 1. Observation of electron beam deflection in the electric field Will voltage electron beam deflection plate to tie the direction switch "is" location, rotating clockwise direction deflection plate voltage Potentiometers (RP2), the electron beam is deflected upward, the greater the voltage between the deflection plate, the electron beam deflection angle the bigger.

实验一。观察电子束在电场中的偏转将电子束偏转板电压方向开关扳到&上正&位置，顺时针方向旋转偏转板电压电位器(RP2)，电子束则向上偏转，偏转板之间电压越大，则电子束偏转的角度越大。

Anhydrous plate wash: An anhydrous alcohol, a water-free alcohol used in lithographic deep-etch plate making to wash the plate before applying tie lacquer image base.

无水洗版液：是无水酒精。在制深蚀版时用来清洗版面，然后在印纹基样上涂上假漆。

Will voltage electron beam deflection plate to tie the direction switch "is" location, rotating clockwise direction deflection plate voltage Potentiometers (RP2), the electron beam is deflected upward, the greater the voltage between the deflection plate, the electron beam deflection angle the bigger.

实验一。观察电子束在电场中的偏转将电子束偏转板电压方向开关扳到&上正&位置，顺时针方向旋转偏转板电压电位器(RP2)，电子束则向上偏转，偏转板之间电压越大，则电子束偏转的角度越大。

To research the effect of pin carding plate on removal of neps in the card slivers,nep tests to the card slivers under different processing conditions using pin carding plate, saw-tooth carding plate and taker-in grid under the card taker-in by USTER AFIS single fiber tester were done.

为研究梳针分梳板对棉结去除的影响，用AFIS单纤维测试仪对梳棉机刺辊下采用梳针分梳板、锯齿分梳板、小漏底在不同加工条件下所加工的生条进行棉结检测，结果显示：1在隔距较小范围内，梳针分梳板去除棉结和SCN能力更强一些；2类分梳板去除棉结和带籽屑棉结能力都比加小漏底方案要好。

Enormous kinds of hub in different shapes are fastened and located by the chuck in various ways, such as fastened with external swing pressure plate and internal hook pressure plate (pressure plate to rotate by 90° to facilitate loading/offloading of workpiece), gripped with claw, and fixed positioning and moveable positioning, etc.

轮毂的品种很多，形状差别较大，卡盘的夹紧和定位方式各不相同，有外部摆动压板夹紧式和内部钩形压板(压板可转位90°，便于装卸工件)夹紧式，还有卡爪抱紧式等，有固定定位式和活动定位式等。

According to structure, butterfly valve can be divided into the following types:- Plate Butterfly - Swash Plate - Offset plate - Leveraged

根据结构形式，蝶阀可分成以下类型：——板式蝶阀——斜板式——偏置板式——杠杆式

In General, allow a printing plate over minutes and slightly smaller film locations, if printing plate dot dot scores color film, the Sun from a printing plate is too deep.

凡是环境下，不准印版比电不合胶片的网不面略小一些，如果印版的网不面比不合色胶片网不面不小些，则暗示晒不入来的印版太浅。

5 Degree of valve opening and closing valves open and close the display plate ① degree of scale line should be cast in the gearbox cover or change the direction of the display after the disc casing, all for the ground wire brush on the phosphor scale to show striking;② direct needle plate material in the case of better management of available stainless steel, or steel plate for the painting, do not make use of aluminum skin;③ direct drive needle eye-catching, stable fixation, accurate adjustment when opening and closing after Rivets should be locked.

4.5 阀门启闭程度的显示盘①阀门启闭程度的刻度线，应铸造在变速箱盖上或转换方向后的显示盘的外壳上，一律面向地面，刻度线刷上荧光粉，以示醒目；②指示盘针的材质在管理较好的情况下可用不锈钢板，否则氧气专用阀、铜阀门为刷漆的钢板，切勿使用铝皮制作；③指示盘针醒目，固定牢靠，一旦启闭调节准确后，应以铆钉锁定。

Our main products include: cast iron inspection plate, crossed plate, welding plate, T-slot assembly platform, boring and milling machine table, coordinate platform, electrical test platform, Fire Works platform, floor boring machine table, magnesium light ping-foot aluminum, cast iron-type ping-ping-foot, bridge-type flat feet, feet, square, angle ruler tool dedicated, inspection box, line box, magnetic box, magnetic V-frame, deflection tester, gear beat tester machine testing wand adjust Sizing Block Machine, Machine Tool Sizing Block earthquake, ladder Sizing Block, contour Sizing Block.

我公司主要生产的产品有：铸铁检验平板、划线平板、焊接平板、T型槽装配平台、镗铣机工作台、三座标平台、电机试验平台、火工平台、落地镗床工作台、镁铝轻型平尺、铸铁平型平尺、桥型平尺、方尺、直角尺、机床专用角度尺、检验方箱、划线方箱、磁性方箱、磁性V型架、偏摆检查仪、齿轮跳动检查仪、机床检验棒、机床调整垫铁、机床防震垫铁、阶梯垫铁、等高垫铁。

It's not quite as simple as that.

并没有那么容易。

It debuted in 1992 in Japan and the United Kingdom, and 1993 in the United States.

它首次亮相于1992年在日本和英国，在美国1993年。