查询词典 patch bolt

Flange joint with high intensity bolt,its bolt screw is not tighten match.

法兰采用高强度螺栓连接，其螺孔不是紧配合的。

"When bolt ing to steel flanges, longer bolt s or stud may be required."

当用螺栓与钢法兰连接时，可能需要更长的螺栓或螺杆。

If not, you'll need to tread the rope through a metal chain, ring, or large ring-shaped bolt hanger (never tread rope through webbing or a regular bolt hanger).

如果不是，那你就必须将绳子穿过铁鍊、O型环、或大孔的耳片（绝对不要将绳子穿过正常大小的耳片内，这样会严重损伤你的绳子！）。

If not, you'll need to tread the rope through a metal chain, ring, or large ring-shaped bolt hanger (never tread rope through webbing or a regular bolt hanger).

如果不是，那你就必须将绳子穿过铁链、O型环、或大孔的耳片（绝对不要将绳子穿过正常大小的耳片内，这样会严重损伤你的绳子！）。

If not, you'll need to tread the rope through a metal chain, ring, or large ring-shaped bolt hanger (never tread rope through webbing or a regular bolt hanger). Start by attaching yourself to both anchors with two quickdraws.

如果不是，那你就必须将绳子穿过铁链、O型环、或大孔的耳片（绝对不要将绳子穿过正常大小的耳片内，这样会严重损伤你的绳子！）。

If not, youll need to tread the rope through a metal chain, ring, or large ring-shaped bolt hanger (never tread rope through webbing or a regular bolt hanger).

如果不是，那你就必须将绳子穿过铁链、o型环、或大孔的耳片（绝对不要将绳子穿过正常大小的耳片内，这样会严重损伤你的绳子！）。

Preload condition, the cylinder head bolt-hole depth of deformation of the cylinder sets a great impact on the proper cylinder head bolt hole depth Shen cylinder l

预紧工况下，缸盖螺栓沉孔深度对气缸套变形影响很大，适当的缸盖螺栓沉孔深度有利于减小气缸套变形。

Preload condition, the cylinder head bolt-hole depth of deformation of the cylinder sets a great impact on the proper cylinder head bolt hole depth Shen cylinder liner to reduce the deformation.

预紧工况下，缸盖螺栓沉孔深度对气缸套变形影响很大，适当的缸盖螺栓沉孔深度有利于减小气缸套变形。

Cylinder, the cylinder sets of radial a surplus deformation of the cylinder sets a great impact on the cylinder liner reduced radial a surplus amount to reduce the deformation of the cylinder sets, the top surface of the body decreases roughness, but it will increase the body on the plane cylinder only mouth the roughness ; Preload reduced cylinder head bolt deformation of the cylinder liner little effect, the body can reduce the top surface roughness and cylinder body on the plane I ended roughness; Shen appropriate reduced cylinder head bolt hole deep can reduce the deformation of the cylinder sets, but will cause the body and the top surface roughness on the cylinder body only I roughness increases Plane .

工作工况下，对于第2缸来说，气缸套径向过盈量对气缸套变形影响很大，减小气缸套径向过盈量，有利于减小气缸套的变形，减小机体顶面不平度，但会增大机体上缸套止口平面的不平度；减小缸盖螺栓预紧力对气缸套变形影响很小，可减小机体顶面不平度和机体上缸套止口平面的不平度；适当减小缸盖螺栓沉孔深可以减小气缸套的变形，但会造成机体顶面不平度和机体上缸套止口平面不平度的增大。

Some of the specimens were interference fit tapered shank bolt connections, and the others were ordinary cylindrical shank bolt connections.

介绍了以7475 T761铝合金为基材的锥形螺栓干涉配合和普通螺栓非干涉配合连接的犬骨形试件，在随机疲劳载荷谱作用下的疲劳试验。

I am a stripper at heart really.

我真的是个心灵的清洁工。

Some,like Leviton's Decora Occupancy Sensor($70),are designed to replace astandard wall switch.Others are ceiling-mounted.

有些人，如立维腾的装扮感应器(70美元)，旨在取代标准的墙壁开关。