查询词典 patch board

By appending a support board hole for vertical column in the middle part of top beam, the height of support board around hydraulic cylinder is decreased.

在上横梁中间结构的立柱孔周围添加了支撑板；减小了中心液压缸周围支撑板的高度。

In the height-calibrating method, after the calibration board is moved twice, the calibration matrix can be got from the relationship between the phase and the height of the calibration board.

通过移动标定平面到两个不同位置，得到标定位置处的光栅图像，根据平面间的相位差和高度差得到高度标定矩阵。

After all the factors were taken into account, 250mm was recommended for both the gap between the board and the bottom of reactor and the liquid height above the board.

权衡诸因素，导流板与反应器底部的距离以及挡板上方的液膜高度宜取250mm，提升区和回落区的面积之比宜取2/3。

Given the same total flow effusion from holes, the results show that the heat shield gets a higher average cooling effectiveness when the opening ratio is 3% compared with 6%; cooling effectiveness is sensitive to the height of ripple board, the heat shield gets the highest cooling effectiveness when the dimensionless height of ripple board is 1% compared with 2% and 3.33%; but there is a little influence on the cooling effectiveness of the liner with the change of the diameter of holes and the height of cooling passage.

研究表明：在气膜孔出流总量相同的情况下，3%开孔率比6%开孔率的隔热屏平均冷却效率较高；波纹板高度对隔热屏冷却效果影响较大，波纹板无量纲高度为1%比波纹板无量纲高度为2%和3.33%的隔热屏平均冷却效率高；孔径和冷却通道高度的改变对隔热屏冷却效果几乎没有影响。

It has no handlebar, one front wheel, one front foot board capable of controlling direction, one rear foot board, one accumulator and one rear wheel between two foot boards, and one wheel hub motor and one brake in the center of the rear wheel.

为了进一步减小传统电动车的体积和重量，本折叠电动车采用无龙头设计，两端各有一个脚踏板，两脚踏板间为蓄电池和后轮，后轮中心为轮毂电机和刹车装置。

The embedded display and control impoldered board basede on ARM9 adopt the chip with ARM9 core as MCU and use multi-peripheral interface and independent the display module.This board can realize the exchange and display for information and multi-communication means and have favorable expansibility and transplantability.

系统的显示与控制开发板采用带有ARM9核的芯片作微处理器，辅之以多种外围接口和独立的显示模块，实现了信息的交换与显示和多种通信手段，提供了良好的人机交互，同时具有良好的可扩展性和可移植性。

Ivory board: Good quality board manufactured by laminating two high quality sheets together.

象牙白纸板：用两张高品质纸张裱合而成的优质纸板。

Company production can be divided into the filter press type manual jack, manual hydraulic, automatic drawing board, PC to control the form of filter specifications have 315 315,420 420,630 630,800 800,810 810,1000 1000,1250 1250,1000 1500,1500 1500,1600 1600,1500 2000,2000 2000,2000 2500 and so has the work pressure 0.6MPa, 1.0MPa, 1.6MPa, 2.0MPa , 2.5MPa, 4MPa, several grades, filters can be adapted to the temperature -40-120 , filtration area of 0.16 square meters from -1600 square meters, able to meet the needs of different users, the company's PC production control, set automatically pull board, Qu Zhang beat, water washing, automatic hydraulic system, etc.

公司生产的压滤机可分为手动千斤顶式、手动液压式、自动拉板、PC控制等形式，滤板规格有315×315，420×420，630×630，800×800，810×810，1000×1000，1250×1250，1000×1500，1500×1500，1600×1600，1500×2000，2000×2000，2000×2500等，工作压力有0.6MPa， 1.0MPa， 1.6MPa， 2.0MPa， 2.5MPa， 4MPa，等几个档次，过滤温度可适应-40-120℃，过滤面积从0.16平方米-1600平方米，能满足各种不同用户的需要，公司生产的PC控制，集自动拉板、曲张振打、水冲洗、自动接液系统等多项功能于一体的全自动压滤机，适用于现代化的企业使用。

Finally, when painting used as finishing layer, the area of EPS board should not be less than 40%, and the flex-waterproofing putty and the elastic painting should be used; when tile used as finishing layer, the area of EPS board should not be less than 80% and the special tile adhesive mortar and the joint filler should be applied.

饰面为涂料时，聚苯板粘结面积不少于40%，应使用柔性耐水腻子和弹性涂料；饰面为面砖时，聚苯板粘结面积不少于80%，应采用专用面砖胶粘剂和勾缝砂浆进行施工。

Highly absorptive nonmetallic material, die-board, was cut by linear polarized CO2 lasers through eight different directions. Effect of laser power, cutting speed and assisted air on the width of the cut kerfs of the die-board was also discussed by contrast with that of lower carbon steel.

为了研究线偏振CO2激光对高吸收率非金属材料的影响，采用线偏振CO2激光沿着不同的方向切割模切板，研究不同激光功率、切割速度、切割方向、辅助气体对切缝宽度的影响，同时对比线偏振激光切割低碳钢。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。