查询词典 parametric curvature

Using the amplification transfer function of type Ⅰ BBO crystal, the theoretical study of spatial properties of the optical parametric fluorescence generated by homochromatic signal and polychromatic signal in optical parametric amplification is investigated, The numerical simulation results demonstrate that when the homochromatic signal is injected into optical parametric amplifier, the fluorescence signal is first emitted in a cone and then in a ring while centering on the pump wave direction.

采用第Ⅰ类相位匹配BBO晶体的放大传递函数方法，分别对光参量放大过程中单波长信号光注入和多波长信号光注入出现的参量荧光的空间特性进行了详细的理论研究。

The error compensation is introduced in the interpolation algorithm to increase the interpolation point's solution precision in the cutting direction of the parametric curved surface. The reasonable simplification of the computed result of the interpolation point's parameter value is carried in the operation process by focusing on the character that curvature of slow-varying parametric curved surface changed slowly and the feature that the scanned profile of translational scanned curved surface is parallel along the scanned line.

通过引入误差补偿值以提高参数曲面在走刀方向上插补点的计算精度，针对缓变参数曲面曲率缓变和平移扫描曲面扫描轮廓沿扫描线平行的特点在运算过程中对插补点参数值的计算结果进行合理简化。

On the basis of OCM, segmentation based on curvature radium is presented in the paper, in which curvature radium is calculated using parametric-surface fitting, and detecting edge points is realized from orthogonal direction, which ensure the integrality of edge points. Since the data is organized by cross-line in OCM, a new arithmetic, Double-direction Angle Difference arithmetic, is brought forward, which can pick up edge points more quickly.

物体的表面一般由多个曲面相交组成，要建立完整的几何模型，需要对测量数据进行区域分割——区分不同曲面的数据，现有的区域分割大多是对单视图的图像式测量数据进行的，但完整的CAD模型需要联合多个视图产生，本文在上面提出的三维正交模型的基础上，提出了三种区域分割方法：第一种方法是基于曲率半径的数据分区方法，通过二次参数曲面拟合计算局部曲率半径，从正交的多个方向进行检测，保证了边点提取的完整性。

Based on this property, by solving a series ODEs we construct a two-parametric family of helicoidal surfaces under cubic screw motion with prescribed mean curvature or Gauss curvature and solve an open problem left by Beneki.

基于这一点，当螺旋面的平均曲率或Gauss曲率为给定光滑函数时，本文选取伪正交标架，使得两类螺旋面的平均曲率和Gauss曲率的表达式相对简化，通过求解一系列的非线性常微分方程，即可确定一族生成曲线，从而最终确定平均血率或Gauss曲率为给定光滑函数的双参数族螺旋面，并在这一过程中解决了Beneki等人留下的一个公开问题。

Applying this rule, we give a kind of definition of discrete Gauss curvature and mean curvature on the discrete parametric curves net.

应用这种加细方法，我们给出了一种针对由离散参数曲线网形成的四边形网格上任意顶点处的离散估计值的定义方法。

Some geometric data of ellipse in hyperbolic space are considered, such as set inclusion, arc length, geodesic curvature, curvature, area and total curvature.

摘要在双曲空间中，考察椭圆的包含关系，对弧长元素、测地曲率、曲率、面积及全曲率等几何量做出细致考察。

Consider the circle that is tangent to the curve at and has the same curvature there. Its center will lie on the concave side of the curve. This circle is called the circle of curvature. Its radius is the radius of curvature, and

在点处的曲线的法线上，在凹的一侧取一点，使得，以为圆心，半径为的圆叫做曲线在点处的曲率圆，曲率圆的圆心叫做曲线在点处的曲率中心，曲率圆的半径叫做曲线在点处的曲率半径。

If we give some restrician to the intrinsic quantities of submanifolds, such as second fundamental form, scalar curvature,Ricci curvature or sectional curvature,then we can get some new property of the submanifolds.The procedure is called pinching problem of submanifolds.

对子流形的第二基本形式模长平方s，数量曲率R，Ricci曲率R_及截面曲率R_等内在量，加以某种限制，从而得到子流形的某些性质，叫做子流形的pinching问题。

On the other hand, Let M~n be an z-dimensional complete noncompactoriented submanifold with finite total curvature in an-dimensional simplyconnected space form F~ of constant curvature c. In this thesis, we provethat if M satisfies one of the following: n≥3, c=0 and integral from n=M H~n＜∞;n≥5, c=-1 and H＜1-2/n~(1/2); n≥3, c=1 and H is bounded, where Hdenotes the mean curvature of M. then the dimension of the space of L~2 harmonic1-forms on M is finite.

本文还证明：若具常曲率c的完备单连通空间型F~中具有有限全曲率的n维完备非紧可定向子流形M满足下面条件之一：n≥3，c=0且integral from n=M H~n＜∞；n≥5，c=-1且H＜1-2/n~(1/2；n≥3，c=1且H有界的，则M上L~2调和1-形式空间的维数是有限的，这里H为M的平均曲率。

Triangular mesh, normal vector, principal curvature, gaussian curvature, mean curvature

三角网格，法向量，主曲率，高斯曲率，平均曲率

It also analyzes the feature and development of semi-finish grinding and finish grinding by roller press.

同时进行了辊压机半终粉磨和终粉磨系统的特点和发展分析。

When I got there, water was dripping slowly from the ceiling and forming a pool on the floor.

当我到那里的时候，水是慢慢地从天花板滴而且形成在地板上的一个池。