查询词典 mechanical engineering

The analysis of the mechanical sensitivity and the density indicated that the system which contained the F rubber, ceresin and graphite had a very good effect on shaping performance and mechanical sensitivity. Both the friction and impact sensitivity were 0. When the pressure reaches to 900 kg/cm2 the density ratio could achieve 99.2%.

对机械感度和压制药柱密度的测量和分析，研究结果表明在九种粘结-钝感体系中，F橡胶、蜡类钝感剂、石墨组成的粘结-钝感体系成型性能和机械感度最为优越，其摩擦和撞击感度都为0.00，900比压时可压系数可达到99.2%。

Helm flywheel:go round and round timing and escapement of Mechanical watches,the equipment's advantage is balance wheel and escapement self-move with 360 degree circumvolve,so high limit minish the effect of gravity,and improve the time veracity ,because gravity will make Mechanical wristwatches bring small difference, helm flywheel setting in order to overcome this difference.

舵飞轮：机械钟表西的&旋转纵擒调快机构&，那种卸置的特色是摇轮战纵横机构在本身运止的异时借可以一讫息360度旋转，所以最小限度加老了天口引力的影响，进步了走时精度。果替地口引力会使机械腕表的走时发生纤细的差同，陀飞轮安装就是往战胜那种差别的。

On the basis of previously research, this paper re-probe into the mechanism of electro-chemist mechanical manufacturing process, making the rational technological parameter, and developing the manufacturing equipment. Through a lot of technology tests, get a lot of labratory data, accordingly, researched the surface feature of the electro-chemist manufacturing process, and deeply discussed its influence on the work piece feature. The last result is that: the electro-chemist mechanical manufacturing process can reduce the low-frequency component significantly, but on high-frequency component, it has little influence, having obviously positive pole flat effect. After manufacture, the tip parts on the surface of the work piece is cut off, there is micro "high land" shape, the parameter for surface roughness is reduced a lot, the surface outline of the work piece is negative, the bearing length rate is cliffy. Also the surface quality of the work piece is improved. This can help to avoid changing the shape, improve the feature of rub, gear and reduce the time to suit. This would also ensure the precision and result in a longer work piece life.

在以前研究的基础上，本论文重新探讨了电化学机械复合光整加工工艺的机理，确定了较合理的工艺参数，对电化学机械复合光整加工设备进行了改进，通过工艺实验广泛地搜集了大量实验数据，依据实验数据，多角度地研究了电化学机械复合光整加工的表面形貌特点，并且从理论上深入讨论了电化学机械复合光整加工表面形貌对工件工作性能的影响，最后得出的结论为：电化学机械复合光整加工对工件原始表面的低频成分有较大程度的降低，而对高频成分影响较小，有明显的阳极整平作用，被加工工件表面的尖峰状凸起被去除，工件表面呈现出微观&高原型&，表面轮廓不平度高度特性参数大幅度降低，工件表面轮廓分布集中，且呈负偏态，轮廓偏斜度为负值，轮廓支承长度率曲线陡峭，工件的表面质量得到综合改善，这对提高零件的抗接触变形能力、改善摩擦、磨损性能、降低工件的磨合时间、提高工件的精度保持性、延长工件的寿命均有利。

Because be mingled with of the sulfide in rolling process steel and rolled steel are coinstantaneous,be out of shape , its want to the influence of the mechanical function of direction of rolled steel length relatively blame rolling direction is mechanical the impact of function is little much.

由于轧制过程钢中硫化物夹杂和钢材同时发生变形，其对钢材长度方向的力学性能的影响要较非轧制方向力学性能的影响小得多。

Thereinto, using VC++ made development through external mode, took ActiveX technology to work out component, parameterized design method and so on, developed and empoldered a mechanical component design system based on ASP, and the paper took two columned level wheel reducer for example illustrated realization remote design process of mechanical part.

其中，利用VC++对UG进行了外部模式的二次开发，同时采用了ActiveX技术进行了组件开发以及参数化设计方法等，研制和开发了一套基于ASP的机械零部件设计系统，并以二级斜齿圆柱齿轮减速器的网络化设计为实例详细地讨论了其远程设计的实现过程。

Firstly, it is difficult to densify CeO2 based solid electrolyte materials and a sintering temperature above 1600℃is required to prepare dense CeO2 based solid electrolyte materials by the conventional solid-state reaction method;Secondly, doped ceria are brittle materials and have weak mechanical strength, which would be susceptible to fracture due to thermal stresses and mechanical stresses during cell fabrication and operation; Thirdly, electronic conduction will be introduced because of the reduction of Ce4+ under low oxygen partial pressure, which would reduce the output voltage and output power of the cells.

其一，CeO_2基电解质材料难以致密化，用常规的固态反应法制备的CeO_2基电解质粉体需要在1600℃以上烧结才能达到致密化；其二，CeO_2基电解质为脆性材料，机械强度低，使其容易在电池的制造及运行过程中由于热应力及机械应力而破裂；其三，CeO_2基电解质在燃料极一侧由于Ce4+还原为Ce3+出现电子导电，降低电池的输出电压和输出功率，影响电池的性能。

By dilatometric change and microscopic test, the critical point at Ac1、Ar1、Ac3 and Ar3 of ML40Cr steel was detemined in Gleeble-3800 the thermal-mechanical simulator. The continuous cooling transformation diagram of ML40Cr steel was obtained by measuring the expanding curves of different cooling rates. The mechanical property and transformation of austenite were analyzed. The proper range of control cooling rate about ML40Cr cold heading steel was found. All those provide the reference for productive practice to develop cold heading steel.

在Gleeble-380热模拟试验机上采用热膨胀法－金相法测定了ML40Cr钢的临界点Ac1、Ar1、Ac3、Ar3，同时测定了在不同冷却速度下过冷奥氏体连续冷却时的膨胀曲线，获得了该钢的连续冷却转变曲线；研究了ML40Cr连续转变冷却过程中奥氏体转变过程和转变产物的组织和性能，初步确定了ML40Cr盘条的控制冷却范围，为冷镦钢ML40Cr盘条的开发提供了参考依据。

Aiming at the disadvantage of mechanical press, this paper proposes a new slide driving structure and press control concept, in which the special positioning module control the position and speed of the slide, so that the slide motion can be discretionarily controlled, it makes the mechanical press produce a variety of workpieces of different technics and materials.

本文针对传统压力机的不足，提出了新的滑块驱动模式和压力机控制方案，并采用独立的定位模块对滑块的位置和速度进行控制，实现了滑块运动规律的任意调节，使机械压力机可适用于多种工艺和材质的加工。

The crystalline composition, microstructure and mechanical properties of experimental lithium disilicate glass-ceramic and IPS e.max Press were compared. No obvious difference in mechanical properties and crystalline composition was found between these two materials.

对比分析了实验二硅酸锂玻璃陶瓷和IPS e.max Press玻璃陶瓷的晶相组成，微观结构和机械性能，探讨了微观结构与性能的关系，并对牙科二硅酸锂玻璃陶瓷的自增韧机制进行了分析。

Employment positions involving senior and junior clerk,senior and junior sales, administration staff, accounting engineeers ,mechanical programmer, mechanical draftman, moulding technician, latheman and miller,construction engineer, draftman, bricklayers, carpenters, steel bender, sewers, aquatic workers , electronics workers, waiters, cooks, Seafarers, the deckhand, karaoke girls, masseuse,manicure and pedicure,unskilled workers, cleaners and other non-technical.

主要外派国家有：新加坡、韩国、日本、科威特，阿联酋、卡塔尔、印尼明丹岛、马尔代夫、加拿大等国家和地区，行业涉及中高级文秘、中高级销售人才、行政人员、会计、工程师、机械设计师、制图员、模具工、车床铣床工、建筑设计师、工程师、制图员、建筑瓦工、木工、钢筋工、缝纫工、水产、电子、服务员、厨师、海员、渔工、卡拉OK女生、按摩师、美甲师、杂工，清洁工人等无技术人员。

Connectors are lines that can be anchored to particular places, called glue points , on the graphic object.

连接符，可固定在图形对象的特定的地方的线条。

Another way of putting it, too many agents have a say in each other's work, and bureaucratic rigor mortis sets in.

另一种表达是，太多的作用物在彼此的工作里都有话语权，官僚的僵尸开始抬头。