查询词典 jointer plane

The oil tube thread jointer used to conduct coating with the compound lubricant when connect the jointers.

以前在油井管螺纹接头连接时，要进行涂覆复合润滑脂。

However if this kind of compound lubricant coating is omitted, it is not only improve the operation environment, but also reduce the total drilling cost. The non-lubricate high quality tube jointer was developed by Nippon Steel Corp.. It adopt the solid lubricant membrane, the fine lubrication and sealing properties insures the same performance.

但省略这种复合润滑脂的涂覆，不但可改善操作环境，也可降低总钻采成本，因此，新日本制铁公司开发出无润滑剂型高级管接头，此接头采用了固体润滑剂被膜，良好的润滑性、密封性等使用性能确保和以前接头同等。

The results showed that the fracture toughness of the weld of HFW pipe was lowest.The value of absorbed energy of HFW weld was closely related to the heat treatment process.But the fracture toughness of fusion zone of submerged-arc welded jointer,its microstructure was coarse granular bainite,and was lower than the other locations of heat affected zone;and with the increasing of steel strength,the effect of welding heat cycles on the pipeline steel became stronger,and form coarse microstructure in fusion zone leading to decrease fracture toughness.

结果表明，高钢级管线钢高频焊接焊缝处的断裂韧性最低，其冲击功大小与热处理工艺密切相关；而埋弧焊接热影响区断裂韧性在熔合线处最低，其主要原因是此处的组织为粗大的粒状贝氏体，而且强度越高焊接热循环对管线钢的作用越强，在熔合线附近更容易产生粗大组织，使断裂韧性降低。

The thesis proposes a confirmation of implicated relation in union of subjective and objective aspects, then differentiates imaginative jointer of offense, absorbable offense, successive offense and combinative offense from implicated offense.

对于牵连关系，本文坚持主客观相统一的观点。另外，牵连犯与想象竟合犯、吸收犯、连续犯和结合犯容易发生混淆，本文对它们进行了区分。

The processing zone includes the processing of board, the furniture processing zone, the product of wood; the business zone includes the log market, and board wood market( the trade of jointer's board, plywood, fiberboard),furniture market, ornament materials market.

加工区包括板材加工区、家具加工区、木制品加工区；交易区包括原木市场、板材市场（经营细木工板、胶合板、纤维板等）、家具市场、装饰材料市场。

Four side moulder series, multi-rip saw series, MDF flooring production line, wood door product line, finger jointer series.

全新型四面刨系列、多片锯系列、实木地板生产线、强化复合地板生产线、实木复合地板设备、实木门生产线、镜框生产线、梳齿接木生产线。

A slim azimuth 20 independent-arm caliper logging tool;2. Design of TFY-1 universal azimuth jointer with a restrained gyroscope;3. The pit shaft parameters of the elevation angle,the azimuth angle,the tool of facial angle and so on are obtained after the computation.

陀螺测斜技术以动力调谐速率，陀螺测量地球自转角速率分量和石英加速计测量地球加速度分量为基础，经计算得出井筒的倾斜角、方位角、工具面角等参数。

The plane lifts quickly, pass through aerosphere, at this moment air man shuts engine, passenger and unit staff have weightlessness feeling, after this kind of case lasts about two minutes, the plane returns aerosphere, the plane is quickened afresh.

飞机迅速升高，穿越大气层，这时飞行员关闭发动机，乘客和机组人员有失重感，这种情形持续大约两分钟后，飞机返回大气层，飞机重新加速。

The common method for obtaining the angle of the plane figure to projection plane is through the right-angled triangle method after getting the double-face projection of the plane figure on the basis of the conception of maximum oblique line.

求平面图形对投影面的倾角，通常需要知道平面图形的两面投影，利用最大斜度线的概念，通过直角三角形法求得。

In the second chapter, elementary theories and ideas of one step forming inverse approach were described and warped modification method, implemented by Cook, was introduced into one step forming simulation and based on idea of surface spreading; new quadrilateral element modification arithmetic was put forward. By spreading warped quadrilateral onto plane in local coordinate system, a plane quadrilateral element whose shape and area were equal to original warped quadrilateral element was gotten and internal force vectors of four nodes and stiffness matrix of elements were improved to increase precision of simulations on this plane element.

第二章从一步成形逆有限元法的基本理论和思想出发，将Cook基于弹性理论的四边形单元的翘曲修正算法引入基于塑性的一步成形，并且基于曲面展开的思想，本文提出一种新的四节点单元翘曲修正方案，通过把翘曲的单元展开的方法在局部参考系中得到一个与实际翘曲单元的形状与面积非常接近的平面单元，在该平面单元中进行单元刚度及内力向量的计算，进一步改善模拟结果的精度。

These are places without aristocratic baggage; egalitarian places open to talent, self-improving, engaged in learning and innovation through networks that were at once competitive and cooperative.

这些地方没有贵族遗风作祟，而且对于那些有天分的人是开放的平等之地，这些人善于通过那些曾经很具有竞争力与合作精神的关系网进行自我提高以及学习创新。

Christine: You don't want to see me?

你不想见我？