查询词典 jam nut

Lead Ph Basic load rating Permissible load F P Nut mass Shaft mass Dynamic rating Ca Static rating C 0 a mm kN kN kN kg kg/m 36 65.9 135 7.4 12.5 Type using standard material Standard grease Standard seal Iron-based Multemp HRL Grease RR Dimensions of the Ball Screw Nut Attached with Wiper Ring W and QZ Lubricator WW avail- ability QZ avail- ability Dimensions including WW L Length of protrusion with QZ attached QWL Outer diameer of protru- sion...

载荷钢球圈列数 DN值预压预压方法预压负荷 2列 3.80圈 160000 有定位置预压 3325 导轨型号丝杠轴加工方式球保持器轴的花键部分中空轴滚珠精密有无无轴承支撑座固定侧的推荐方式轴承支撑座支撑侧的推荐方式螺母种类螺纹方向间隔钢球 BK40 BF40 简易螺帽右螺纹无轴方向刚性螺纹条数防尘措施防尘罩形式 W清洁环。。。

Lead Ph Basic load rating Permissible load F P Nut mass Shaft mass Dynamic rating Ca Static rating C 0 a mm kN kN kN kg kg/m 10 27.6 63.3 2.75 6.51 Type using standard material Standard grease Standard seal Iron-based AFB-LF RR Dimensions of the Ball Screw Nut Attached with Wiper Ring W and QZ Lubricator WW avail- ability QZ avail- ability Dimensions including WW L Length of protrusion with QZ attached QWL Outer diameer of protru- sion with QZ at...

载荷钢球圈列数 DN值预压预压方法导轨型号 2列 2.50圈 70000 无无滚珠丝杠轴加工方式球保持器轴的花键部分中空轴轴承支撑座固定侧的推荐方式精密无无无 BK25，FK25 轴承支撑座支撑侧的推荐方式螺母种类螺纹方向间隔钢球轴方向刚性 BF25， FF25 单一螺帽右螺纹，左螺纹，左右螺纹无 680.0 螺纹条数。。。

The double ends of central tube is penetrated into pipe union nut, chuck ring and seal ring in turn, and the central tube is penetrated into ladder-shaped public connection, push the seal ring and chuck ring of double end into the ladder-shaped public connection separately, the thrash pipe union nut is heave, is credible tight connection.

将中心管两端依次穿入由壬螺母、压环、密封圈，并将中心管穿入梯形公接头内，分别将两端的密封圈，压环推入梯形公接头内，锤击由壬螺母凸起，即可靠密封连接。

The double ends of central tube is penetrated into pipe union nut and seal ring in turn, and the central tube is penetrated into ladder-shaped public connection, push the seal ring and chuck ring of double end into the ladder-shaped public connection separately, the thrash pipe union nut is heave, is credible tight connection.

将中心管两端依次穿入由壬螺母、密封圈，并将中心管穿入梯形公接头内，分别将两端的密封圈，压环推入梯形公接头内，锤击由壬螺母凸起，即可靠密封连接。

The double ends of central tube is penetrated into pipe union nut,chuck ring and seal ring in turn, and the central tube is penetrated into ladder-shaped public connection separately,the thrash pipe union nut is heave,is credible tight connection.

将中心管两端依次穿入由壬螺母、压环、密封圈，并将中心管穿入梯形公接头内，分别将两端的密封圈，压环推入梯形公接头内，锤击由壬螺母凸起，即可靠密封联接。

According to the principles of tooth meshing and manufacturing helicoi ds, a mathematics model is constructed to reflect the manufacture process of nut , and the formula of the grinding wheel section is developed. The parameters of the section are obtained through numeral arithmetic; moreover the parameters of the dresser are worked out. Based on these work, the solid model of the ball scr ew nut, grinding wheel and tooth dresser are developed in the Pro/E software, wh at's more, the process of the dressing...

根据螺旋面加工原理、齿形啮合原理及回转面砂轮加工螺母工艺建立了相应的数学模型，并推导出砂轮截形的计算公式；采用数值计算方法求解砂轮截形参数，进一步得到修整器靠模板的参数；在此基础上，利用Pro/E软件对大导程滚珠丝杠螺母、砂轮和砂轮修整器进行了实体建模，并对砂轮的修整过程和螺母的加工过程进行了运动仿真，有效地验证了砂轮截形的计算结果。

Locking nut is the key component of electrical operated screw tire shapping and curing press for producing and transferring locking force,therefore the correct design of locking nut directly related to the performance and reliability of tire shapping and curing press with screw type.

因此正确设计锁模螺母直接关系到螺旋式轮胎定型硫化机的性能和可靠性，锁模螺母的正常工作既保证了整机运行的稳定性和对中精度，又保证了轮胎制品的质量。

The disk spring fixed on the adjusting nut pushes the screw nut through pressure bearing.

碟形弹簧靠在调节螺母上且经压力轴承分别抵压丝杆螺母。

The screw nut is of double nut tube type which is single tube 2.5 circuits.

该滚珠丝杠副是双螺母外循环方式的，循环组数为1组2.5圈。

Shaft Type Linear Guide,Linear Ball Bearing,Shaft ,Oilless Bearing ,Linear Guideway,Ball screw,Coupling,Support unit,Safety Bearing Nut,Luck Nut,Unive...

轴心式滑轨，线性轴承，特殊自润轴承，轴心，线性滑轨，滚珠螺杆，联轴器，螺杆支持座，防松螺帽，锁定螺帽。。。

This paper designs the communication system of radio telescope FAST.

针对500m口径球面射电望远镜FAST分布式控制系统的特点完成了其通信系统的设计。

Political sheep's step-by-step a large number of fossils unearthed in the county soil Ma Ali after rural village in the middle of sallow pelitic siltstone.

步氏和政羊化石大量出土于广河县阿力麻土乡后山村，产于灰黄色泥质粉砂岩中。