查询词典 graphical calculation

The systemic analysis on coal-pulverizing system calculation is made, and some concrete calculation methods and problems are discussed.

论文综合分析研究了目前我国燃煤电站使用的几种主要磨煤机及其制粉系统的性能，分析了它们各自的特点和燃料适用范围，又对制粉系统的计算进行了系统的研究，就一些具体计算方法和问题做了探讨，根据计算、分析和比较的结果，编制了制粉系统的计算软件，对两个运行的制粉系统进行了校核计算，计算结果符合实际。

Winch the type of construction, structure, design, calculation and application we need to fully understand that the overall design of the building winch, from various parts described the choice of the main electrical power, the transmission ratio calculation and validation; reducer design; rope's choose including the selection of a rope, use and reel in the fixed reel; reel involved in the calculations, the design and structure commonly used materials, rope reel capacity size parameters; is the last of the clutch and brake design, the main cone used friction with brake and clutch.

建筑卷扬机的种类、结构、设计、计算及应用需要我们充分的了解，在对建筑卷扬机的总体设计中，从各个部件出发，主要叙述了电动机功率选择、总传动比计算与校验；减速器的设计；钢丝绳的选择包括了钢丝绳的选取、使用及在卷筒上的固定；卷筒的设计计算涉及卷筒结构和常用材料、卷筒容绳尺寸参数；最后是有关离合器与制动器的设计，主要采用了圆锥摩擦离合器和带式制动器。

But, undercut technology may deteriorate the stresss concentration. In order to improve the situation, for a crank throw of a given ductile iron crankshaft, finite element analysis is conducted. The analysis result is optimized and related fatigue calculation is carried out. A compare between calculation and test results is performed and compared results show that conculation result is reliable. Therefore a good undercut structure is found and the reliability of crankshaft is improved.

球铁曲轴加沉割槽往往会加大曲轴的应力集中，根据某厂设计的球铁曲轴，本论文利用有限元分析的方法，对其单拐曲轴的沉割槽进行有限元模拟分析，在分析结果的基础上进行优化设计，最后得出较好的沉割槽结构，从而得到较好沉割结构，提高曲轴的可靠性。

The adaptability of arch dam to geology is more and more high, when the influence of complicated geology is considered, and the widespread used modern calculating methods in engineering, such as the finite element method, is considered during optimization design, the new challenge to old optimization design system of crown cantilever analysis is the full-automatic calculation problem of the different condition, different arch dam parameter, the possibility and the efficiency which were caused by the increments of calculation time.

高拱坝设计对地质条件的适应性要求越来越高，优化设计时要考虑到复杂地质条件的影响，最好采用已被工程界普遍接受的有限单元法等现代计算方法，这对以拱梁分载法为主的拱坝优化设计体系提出了新的挑战，除了需要解决不同条件、不同拱坝参数的全自动计算问题，还要解决由于结构计算时间增加所带来的优化计算的可行性和效率问题。

Be familiar with electrical design and electrical calculation, i.e. sizing transformer, calculation of short circuit current , circuit breaker setting

熟悉工厂变配电系统的设计及整定计算，如变压器容量计算，系统短路电流计算及开关整定计算等。

Finally this paper achieves a new method about Modeling and simulation of the liquid cargo tank. 3 The calculation of tank capacity based on UG/CAD modeling is studied in this paper . The calculation datum point is gotten by interposition of ship hull at first. Then many datum plane that go through different sounding and heel is created . The cad modeling of oil is created by the bool of the datum plane and the cad modeling of tank.

在使用UG建立准确的计量舱满舱CAD模型的基础上，采用插值得到计量舱计量基准，根据不同测深和不同纵倾值，建立一系列计量液位面，计量舱满舱CAD模型和计量液位面布尔运算后得到实际油液的CAD模型，通过计算油液CAD模型的体积，实现对计量舱容积的计量。

Secondly, in the dissertation, the theories and methods of calculation on bridge deck system were discussed, and bridge deck system simplified as a beam was analyzed with the theory of elastically supported continuous beam and the method of deformation compatibility; through the theory of orthotropic plate being applied to analyzing the bridge deck system which was assumed an elastically supported continuous plate, certain theoretical derivations were made and some calculation formulas were given.

其次，本文研究论述了桥道系的计算理论和方法，将桥道系简化为梁，利用弹性支承连续梁理论和变形协调法进行分析；把桥道系视为弹性支承连续板，利用正交异性板理论进行分析，作了一定的理论推导，并给出了相关计算公式。

Based on the research progress abroad,calculation method of deflection due to short-term loads and calculation expression of effective moment of inertia for concrete beams reinforced with FRP bars were brought forward.

在国外有关成果的基础上，给出了FRP筋混凝土梁的挠度计算建议方法及&有效惯性矩&的表达式，同时提出了设计时不需进行挠度验算的最大跨高比限值的计算公式及相应的基于挠度控制的承载力设计方法，对工程应用有着实际的指导作用。

3The dissertation makes a deep analysis on the calculation of the equivalent instantaneous inductance of wye-connected transformer. It concludes that the looping current in the winding of delta side of transformer, which is hard to obtain from line current, severely influences the calculation result of equivalent instantaneous inductance. In that case, a new scheme of transformer differential protection is proposed.

深入分析了变压器 Y/Δ接线方式下等效瞬时电感的计算问题，针对Δ侧绕组环流对等效瞬时电感计算结果影响大，而又无法通过线电流计算得到的特点，提出一种变压器差动保护 TA 配置新方案。

The main functions of this system are medical record management, measurement of dental arc width, measurement of dental arc length, calculation of Spee's curve distance, calculation of crowding degree, angle measurement, Bolton index analysis, mixed dentition measurement and analysis, statistical analysis, specialist system, and so on.

系统的主要功能包括：病历管理、牙弓宽度测量、牙弓长度测量、Spee氏曲线距离计算、拥挤度计算、角度测量、Bolton指数分析、混合牙列期测量分析、统计分析，以及专家系统，等等。

After explaining total design of automated test system for microcircuit , the thesis introduces GPIB standard .

文章在说明了微电路模块自动测试系统的总体设计后，对GPIB标准进行了介绍。

He interceded in my behalf.

他替我说情。