查询词典 fiber graphite

The research which is the important part of the tunable erbium-doped fiber laser is composed of two main parts: 1. the gain part of the tunable erbium-doped fiber laser, which in fact is an erbium-doped fiber amplifier, its output characteristics are discussed both in theory and experiment, and the differences are also discussed between theory and experiment; 2. the saturated absorber part of the tunable erbium-doped fiber laser, also the part to narrow the line width of the fiber laser. The line-width narrowing mechanism in fiber laser induced by unpumped Er-doped fiber is presented from the aspect of coupling wave equation, and the main factor is considered as the standing wave induced by interference. The line-width is narrower when the standing wave is stronger, and the narrowing effect disappears with the disappearance of the standing wave. In the experiment, when adding a Faraday mirror in the laser cavity to remove the standing wave , the narrowing effect disappears. So the theory is proved by the result of the experiment.

本课题的研究内容是集成光学声光可调谐掺铒光纤激光器的重要组成部分，主要分两部分：1、声光可调谐掺铒光纤激光器中增益部分的研究，相当于对掺铒光纤放大器的研究，理论上对掺铒光纤放大器的输出特性进行分析，实验上实现了掺铒光纤放大器系统，并将实验数据与理论计算数据进行对比，分析了误差产生原因；2、声光可调谐掺铒光纤激光器中饱和吸收体部分的研究，即压窄光纤激光器输出线宽的研究，从耦合波方程出发，理论上解释了未泵浦掺铒光纤压窄光纤激光器线宽的原理，分析了影响该作用的主要因素是未泵浦掺铒光纤中相对传输的光干涉形成的驻波：驻波越强，压窄效果越好，相反当没有驻波时，没有压窄效果，在实验上通过在激光器腔内加入法拉第旋转镜使驻波消失，同时压窄效果消失，从而验证了理论分析的正确性。

Firstly, take polyester short fiber, nylon short fiber and cotton powder short fiber for examples, a study was made on the influence of content and kind of short fibers on physical and heat aging properties of short fiber-CR composites. The experiment results showed that the rigidity of the composite increased as the content of the fiber increased, and the tear strength, the modulus at 20% in L direction also increased; thereinto, the reinforcement effect of nylon short fiber was the best, and the cotton powder short fiber was the worst.

第一，以聚酯短纤维、尼龙短纤维、棉粉短纤维为例，研究了短纤维的用量和种类对短纤维-氯丁橡胶复合材料力学性能、耐热性能及其溶胀性能的影响；结果表明，随纤维含量的增加，短纤维-CR复合材料的硬度不断增大；在L向拉伸时，撕裂强度、定伸应力不断提高；尼龙短纤维的补强效果优于其它两种，棉粉短纤维的最差；随纤维含量增加，短纤维-CR复合材料整体耐热老化性得到了极大提高，其中尼龙短纤维-CR复合材料的耐热老化性明显优于其它两种；随纤维含量的增加，短纤维—CR复合材料的耐溶胀性能明显提高；短纤维-CR复合材料的性能呈现明显的各向异性。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Cyclic voltammetry indicated that there were Cr→Cr, Cr →Cr oxidation reaction on anode, while there were Cr→Cr, Cr→Cr, Cr →Cr deoxidization reaction on cathode. The graphite electrodes treated by acid and heating could enhance the reversibility and kinetic of the electrode reaction. The nature graphite electrodes had been eroded during charge/discharge process, while the graphite electrodes by activation could avoide corroding by hexad chromium ion. The reversibility and kinetic of the electrode reaction of chromium ion on activation electrode had been increased, so which indicated that graphite surface augment oxygenous function corps which could increase electrode hydrophile capability.

循环伏安实验表明：铬液流电池的电极反应非常复杂，在阳极存在Cr→Cr，Cr→Cr的氧化反应，在阴极存在Cr→Cr，Cr→Cr，Cr→Cr的还原反应；热处理的石墨电极和重铬酸钾处理的石墨电极能提高电极反应的活性和可逆性；在充放电实验中未处理的石墨电极发生严重腐蚀；分别用这两种方法处理过的石墨电极具有防止六价铬侵蚀的功能；铬离子在活化处理过的石墨电极上的反应活性和可逆性增加，可以认为：重铬酸钾溶液活化处理和加热处理后的石墨表面的含氧官能团增加，电极亲水性增强。

Because of the nondirectional property of ionic bond and the fully delocalized property of pi electrons on carbon layers, translation will not change the electronic structure of carbon layers, resulting in that A-GIC and AE-GIC hare quite good lubrication as well. The electrons come from metals mainly transfer to the delocalized pi orbitals of carbon layers, and the increase of delocalized electrons will make metal graphite intercalation compound more electro-conductive than graphite itself. Because ionic bond between metals and carbon layers is weaker and its lattice energy is much less than that of typical NaCl crystal, so metals could be left from interlayers. The Mulliken populations of C-C in intercalation compounds are smaller than that of graphite, and the HOMO energy level of GIC is higher than that of graphite too. These Lead to that GIC will easier be oxidized.

由于离子键没有方向性，又由于碳层中的π电子是充分离域的，所以碳层不会由于平移而改变其电子结构，金属石墨层间化合物仍具有很好的润滑性；金属失去的电子主要转移到碳层的离域π轨道中，碳层离域电子增多使金属石墨层间化合物的导电性比石墨增强；金属与碳层间的离子键强度比较弱，其晶格能远小于典型的离子晶体，因而金属易从石墨层中脱出；金属石墨层间化合物中的C-C间Mulliken布居值小于石墨中C-C间的值，且金属石墨层间化合物的HOMO能级也高于石墨的HOMO能级，所以石墨层间化合物中的碳原子较石墨更易被氧化。

The hydrogen chloride producing design needed the whole optimization design-aside of two-appulse-one hydrogen chloride graphite synthetic furnace system. With the analysis on the relation of different types of chillers and the productive forces, the YKB round pass graphite chiller, endwise wing drivepipe graphite cooling pipe and equipment design methods for graphite chiller modality were adopted.

氯化氢生产设计中缺少对二合一氯化氢石墨合成炉系统的整体优化设置，通过冷却器形式和系统生产能力的关系研究，确定石墨冷却器采用YKB型圆块孔式石墨冷却器，石墨冷却管采用纵向翅片管型套管式石墨冷却管。

By thermodynamically and dynamically calculating and analysing ,a new growth mechanism of spherical graphite has been proposed ,that is,the spherical graphite does not grow inwardly,but grow outwardly and when spherical graphite grow outwardly carbon atoms come into and fill-up the entocoele of spherical graphite by the diffusing way.

通过对石墨球最终表面的形态进行分析，可以获得气泡的表面并不是石墨球的最终表面，石墨球表面主要由于受到石墨球表面各微晶长大速度不均匀性、铁水中的三大起伏、微量元素与碳原子的竟相吸附、由于浓度梯度和温度梯度所引起铁水的对流等各种因素的综合影响结果使其表面成为凹凸起伏的形状

Selection of our products well, pure texture, the choice of materials are: acrylonitrile-butadiene rubber, silicone, ethylene-propylene rubber, fluoride plastic, hydrogenated nitrile, Poly-resin, folder cloth, rubber, PU expected, polytetrafluoroethylene, nylon, POM, engineering plastics (such as high-strength performance PPS, PEEK) and graphite (such as ordinary graphite, high - Pure graphite impregnated graphite), ceramics, alloys, Pan-gen, synthetic materials, etc.

我们的产品选材精良、质地纯正，选用的材料有：丁腈胶、硅胶、乙丙胶、氟胶、氢化丁腈、聚安脂、夹布、橡塑、PU料、聚四氟乙烯、尼龙、聚甲醛、工程塑料（如高强性能PPS、PEEK等）；及石墨（如普通石墨、高纯石墨、浸渍石墨）、陶瓷、合金、盘根、合成材料等。

Selection of our products well, pure texture, the choice of materials are: acrylonitrile-butadiene rubber, silicone, ethylene-propylene rubber, fluoride plastic, hydrogenated nitrile, poly - Fat, folder cloth, rubber, PU expected, polytetrafluoroethylene, nylon, POM, engineering plastics (such as high-strength performance PPS, PEEK) and graphite (such as ordinary graphite, high-purity graphite impregnated Graphite), ceramics, alloys, Pan-gen, synthetic materials.

我们的产品选材精良、质地纯正，选用的材料有：丁腈胶、硅胶、乙丙胶、氟胶、氢化丁腈、聚安脂、夹布、橡塑、PU料、聚四氟乙烯、尼龙、聚甲醛、工程塑料（如高强性能PPS、PEEK等）；及石墨（如普通石墨、高纯石墨、浸渍石墨）、陶瓷、合金、盘根、合成材料等。

The system can be widely used in belt weighing and batching process control,etc.

介绍了基于智能模糊控制的嵌入式配料系统的设计方法，对模糊PID控制过程和系统调零作了重点的讨论，同时给出了PID控制的程序流程图和系统定长调零子程序。

"I dunno," she answered,"but if you show me aroun', I'll recognize it from the lighthouse just outside the porthole."

"我不知道，"她回答说，"如果你能带我转转，我能认出来的，因为灯塔就在舷窗外。"