查询词典 elastic coefficient

Based on Three Gorges Project, the following aspects about the three typical embedding manners are studied:(1) The border condition of cyclic symmetry is applied to the finite element models with contact among cushion layer, penstock and concrete. The effects of elastic modulus, thickness and placement extent of cushion layer on the stress of its around concrete are analyzed. It is suggested that the ratio of thickness to elastic modulus can be used as an important parameter in the design of cushion layer.

因此，本文结合三峡工程建设实践，在收集和总结前人经验的基础上，以大型通用有限元分析软件ANSYS为平台，对不同埋设方式的巨型蜗壳结构进行以下几个方面的研究：(1)引入循环对称边界条件，考虑垫层-钢板-混凝土之间的接触摩擦，建立有限元模型；并对垫层敷设范围、垫层厚度和弹性模量等设计关键参数进行了优化，并把"垫层弹性模量与垫层厚度之比"作为参考指标进行设计。

Numerical examples are studied to demonstrate the accuracy of the proposed method and to investigate the distribution of the optimal stiffness of the elastic restraints, the deformation of the elastic restraints and deflection of the stiffened plate for stiffened plate with different number of stiffeners, different cross section of stiffeners and different thickness of plate.

本研究利用牛顿法提出一个数值程序以求得使目标函数有最小值且满足拘束条件的弹性支承刚度，即求得最佳化的弹性支承刚度。本研究以数值例题探讨不同加劲板之最佳化的弹性支承刚度，弹性支承变形的分布及加劲板的最大挠度。

It is found that in certain water ratio and consolidation pressure, the values of initial elastic modulus and principal deviator stress increase with intermediate principal stress increasing; in certain intermediate principal stress, the values of initial elastic modulus and principal deviator stress increase with water ratio falling.

试验结果表明：在一定的含水率和固结压力下，偏差应力和初始切线模量均随中主应力比b的增大而增大；在中主应力比b确定的情况下，偏差应力和强度最大值随着含水率的增大而减小。

The centerline of elastic rod or elastic filament can be abstracted as space curves to deal with them by the knowledge of the theory of space curve and differential geometry.

由于弹性杆的中心线或弹性细丝可以抽象成空间曲线，然后根据空间曲线论和微分几何的知识进行处理。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

ABSTRACT Photoplasticity is a method using the high polymer model with the transparent double refraction phenomenon and defining the object's elastic-plastic strain field by the optical image stripe which went beyond the elastic limit.

光塑性法是应用具有透明双折射现象的高分子材料的模型，由超过材料弹性极限下模型的光学图象条纹来确定物体弹塑性应变场的一种方法，这种方法又称为非线性光力学法。

In this paper, a detail analysis of the circumferential through-crack in the cylindrical shells with different boundary restraints is performed by means of the elastic-plastic finite element method. The results obtained provide the application of some analysis methods of elastic-plastic fracture parameters such as Dugdale model with a necessary theoretical base.

本文针对柱壳周向壁穿裂纹，利用弹塑性有限元的数值解，在不同的约束条件下进行了较为详细的分析，获得了一些带有规律性的结果，为Dugdale模型等一些弹塑性断裂参数计算方法的应用提供了必要的理论基础。

Based on the calculated elastic constant, the elastic moduli of characteristic plane (101) are figured, which offers reference to mechanical study of these materials afterward.

根据计算的弹性常数绘制了这些材料特征平面(101)面的弹性模量图，为这方面材料的力学研究提供参考。

High-elastic and constant elastic alloys, low expansion and fixed-expansion alloy.

高弹和恒弹性合金，低膨胀和定膨胀合金等。

In the base of calibrating the elastic constant of cantilever and analysis adhesion force, the force information from force curve was obtained and the elastic modulus of single voxel was calculated.

考虑了成型点剩余部分形变对结果分析的影响，在标定微探针弹性系数和对粘附力进行分析的基础上，提取了力曲线中所包含的力学信息，推算出了成型点的弹性模量，得到了成型点的弹性模量低于宏观材料弹性模量的结论。

I go to school at night.

我是上上学。

Clear Tip Nasal Aspirator: A soft time and gentle suction action makes removing excess mucus easy.

鼻吸明确提示：一个柔软的时间和温柔吸力行动使消除过剩的粘液容易。