查询词典 die block

The author studied the motion compatibleness of executive system, and built the connection of the motion parameter (motion-stand ratio) that complete "walk paper" craft and the bar dimension of die cutting toggle press mechanism that complete "die cutting" craft.

研究分析了主执行系统运动协调性，建立了完成"走纸"工艺的平行分度凸轮的运动参数和完成"模切"工艺的肘杆机构构件尺寸之间的关系。

Concavo-convex business card printing and membership card making two stempelsysteme to a pair of stempelsysteme: one is a recesseda image die (with engraving business card printing and membership card making), the other is a convex image die together.

矮矮制卡和会员卡制息需给两块印模来构不败一差印模：一个是凹进去的图像模（同雕版制卡和会员卡制息差别），另一个是凹下来的图像模。

Feasibility of production and reliability of die design can be guaranteed by concurrence of simulation with technologyand die design.

最后指出工艺与模具设计和仿真并行，可有利保障生产工艺的可行性和模具设计的可靠性。

Wedge mechanism was adopted in piercing die to achieve side piercing, and the positioning of taper pipe depended upon the conical surface of blanking die itself.

在冲孔模中选用了带有楔角的斜楔机构来实现侧冲，并利用冲裁凹模自身的锥形面实现了锥形管的定位。

Your eyes cose, I die; your eyes open, I come back alive. Your eyes close and open again and again, I die and come back time after time.

你的眼睛闭上，我的魂就飞；你的眼睛睁开，我的魂又回；你眼睛眨呀眨，我就死去活来千百回。

The article discusses causes and eliminated measures of aluminium alloy die forging s crassitude crystal from four sides of component,technical parameter,temper of die and heat treatment.

从锻件的材质、锻造工艺参数、锻模温度、热处理工艺参数四个方面，阐述了铝合金模锻件粗晶缺陷的产生原因及消除措施。

The article discusses causes and eliminated measures of aluminium alloy die forgings crassitude crystal from four sides of component technical parameter temper of die and heat treatment .

从锻件的材质，锻造工艺参数，锻模温度，热处理工艺参数四个方面，阐述了铝合金模锻件粗晶缺陷的产生原因及消除措施。

Antigone is here to rebel and die; Creon is the unwilling king; Eurydice's role is but to die in her room; the guardsmen emblematicize the common rank-and-file.

安提戈涅是这里叛乱和模具； Creon是不愿意国王欧律狄刻的作用，但死在她的房间；的卫队emblematicize共同佐级。

4 Move cross hair to the upper side of the die (but not on the die corner due to possible chip out) search for unique pattern. Press ENTER.

移动跟踪球到模的上部，(由于可能离开模所以不是在模的角落)然后寻找独特的模式，按" ENTER "确定

2 Referring to the vision monitor, using tack ball, move cross hair to the die surface. Press "1" for die contact search.

参照显示器，使用跟踪球移到标线到晶片表面，按"1"瓷嘴会探测晶片的高度。

After explaining total design of automated test system for microcircuit , the thesis introduces GPIB standard .

文章在说明了微电路模块自动测试系统的总体设计后，对GPIB标准进行了介绍。

He interceded in my behalf.

他替我说情。