查询词典 deflection system

This paper calculates the strength section, flexural stiffness and deflection ofconcrete plate unbonded prestressed CFRP-lamina.

同时也对无粘结预应力碳纤维板材加固混凝土抗弯构件的正截面强度、抗弯刚度以及挠曲变形进行了计算。

Three actuation mechanisms of piezoelectric composite structures are studied: extension actuation mechanism, shear actuation mechanism and hybrid actuation mechanism Tip deflection of piezoelectric composite plate is analyzed for different actuator layer thickness. The research result can be used for mode control of active noise and vibration control and static shape control of intelligent structure.

研究了压电材料复合板的3种作动机制，弯曲作动机制、剪切作动机制、混合作动机制，针对粘贴在纤维板上不同厚度的压电作动层，具体分析了复合板的端部位移，研究结果对噪声和振动的主动控制中的模态控制和智能结构静态形状控制提供了一定的参考。

Using the concept of the of weighted residual method and choosing the fifth B-spline as a trial function to meet the needs of boundary conditions,the mechanical problem of large deflection of a rectangular thin plate is discussed.

采用加权残值法探讨大挠度力学问题时，用5次B样条作为未知函数的试函数，使其直接满足边界条件，这种方法与传统的有限元法相比，具有未知量少，自由度少，连续性强，边界条件容易满足等优点

Numerical examples are studied to demonstrate the accuracy of the proposed method and to investigate the distribution of the optimal stiffness of the elastic restraints, the deformation of the elastic restraints and deflection of the stiffened plate for stiffened plate with different number of stiffeners, different cross section of stiffeners and different thickness of plate.

本研究利用牛顿法提出一个数值程序以求得使目标函数有最小值且满足拘束条件的弹性支承刚度，即求得最佳化的弹性支承刚度。本研究以数值例题探讨不同加劲板之最佳化的弹性支承刚度，弹性支承变形的分布及加劲板的最大挠度。

In static analysis, small deflection theory of circular plate and electrostatic actuating theory are adopted to simulate electrostatic-structural coupled process. In modal analysis, harmonic response analysis and nonlinear transient dynamic analysis of pump membrane, the fluid in the pump is regarded as an additional mass acting on the pump membrane to approximately substitute the effect of fluid field on pump membrane, which reduces the amount of calculation and improves simulation efficiency.

其中在静态分析中，利用圆型薄板的小挠度变形理论和微机电系统中的静电力驱动理论来模拟静电－结构耦合过程；在泵膜的模态分析、谐响应分析以及非线性瞬态分析中，把腔内的流体当作附加质量作用在泵膜上，近似代替流场对泵膜的影响，从而减小计算量，提高了仿真效率。

Based on the mechanical analysis of rotary pan, the axisymmetrical model and non-axisymmetrical one were proposed respectively by simplifying the effect of lacing wires on pan into ring distribution uniform load or force and were solved according to the flexure theory of thin plate with small deflection.

在分析工作状态下转子圆盘受力的基础上，将拉筋对圆盘的作用分别简化成环形均布载荷和集中载荷，建立承压圆盘的轴对称模型和非轴对称模型，并根据薄板的小挠度弯曲理论，对力学模型进行求解。

Yet for thickness shear actuators, due to the shear deformation dominates the plate deflection for shear actuation mechanism, the higher order shear theory can provide more accurate evaluation of the shear strain energy of the plate than the first-order o

但对于厚度剪切型激励器而言，由于激励器主要是引起板的剪切变形，而高阶剪切变形理论比一阶剪切变形理论能更好地反映结构的剪切应变能，因此高阶剪切变形理论可以提供板变形的更为精确的解。

Experimental study of deflection based on half-metal tube package fiber Bragg grating . Chinese J.

光纤布拉格光栅的半金属管封装及挠度实验研究。

So it is necessary to calculate the strength and deflection of the tube tower.

管塔杆身横截面分为薄壁圆形和正多边形 2类。

It is a difficult work to calculate the deflection of filament wound tapered tube at bending because of changing layer thickness in every cross section.

本文以传递矩阵法为基础，计算纤维缠绕锥管在弯曲载荷作用下的挠曲变形，并以实验结果验证了计算结果。

Yet, Edith says, there was always money in the bank.

但是Edith说，她的银行户口里面总是有钱。

We have created a series of files that resolve this problem--one for each day of the 40 days of purpose.

我们制作一系列的档案去解决这问题---一个为标竿40天中的每一天。