查询词典 cracking

In fact, this cracking is due to the cement wall cracks, or the wall "insulation board" of the joints caused by cracking, not the quality of the decoration.

事实上，这裂缝是由于水泥墙体裂缝，或墙体"保温板"的接缝开裂造成的，而不是质量的装饰。

Make incomplete heavy oil or olefin base crude oil comes to those who raise light oil close through deepness treatment method rate, finished product can serve as after classics of the benzine of generation, derv is purificatory, shan of the cent that weigh heat up in a steamer can serve as catalytic cracking or thermal cracking raw material, coke can serve as the raw material of production electrode, have ask rest method and continuous method etc.

使残重油或石蜡基原油通过深度加工方法来提高轻油的收率，产生的汽油、柴油经精制后可作为成品，重馏分汕可作为催化裂化或热裂化原料，焦炭可作为制造电极的原料，有问歇方法和连续方法等。

On the basis of the principles and structures of the cold cracking implant testing machine,the study on the implant equipment of reheat cracking test is reviewed in this paper.

在深入分析冷裂纹插销试验机的原理和结构的基础上，本文进行了插销式再热裂纹试验装置的研究工作。

Accordingly, the accident of sulfide stress corrosion cracking should be taken into account.The SSCC sensitivity and cracking time of 16Mn steel used to make the cold-high pressure segregator and common 16Mn steel in solutions with various H2S contents and pH values, simulated solution and operating solution were investigated by constant strain bend and slow strain rate test.Hydrogen diffusion coefficients of 16Mn steel, 16Mn steel and their welded seams were also tested by the electrolyte hydrogen charged method.Safety evaluation of the cold-high pressure segregator was given with above results.

针对制造过程中由于开孔失误而进行补焊的冷高压分离器在高压、高浓度的H2S环境的使用安全问题，采用了电化学充氢、恒应变和慢拉伸的实验方法，研究了制造冷高压分离器的主体材料16Mn钢和普通的16Mn钢及其焊缝的氢扩散系数，在不同H2S浓度、pH值，模拟冷高压分离器操作环境溶液和实际溶液中的腐蚀规律和硫化氢应力腐蚀开裂敏感性，结合实际腐蚀环境的检测和分析结果，对补焊后的冷高压分离器的使用安全给出了综合评估。

A Material nonlinear finite element analysis for the cast-in-place reinforced concrete hollow slab that occurs from initial loading, cracking, yielding to failing is carried on. The cracking load, ultimate load, the displacement rules and the principal stress distribution rules of the hollow slab under the vertical loads are obtained. A Material nonlinear finite element analysis for the single span hollow flat-plate floor is also carried on. The function of the concealed wide-flat beams is definite by analyzing the principal stress distribution diagram. The calculating results verify the theoretical analysis and give some important conclusions which are great useful to improve the constructing of the new flat-plate floor.

其次对空心板进行了从加荷、开裂、屈服直至破坏的全过程材料非线性有限元计算，得到了空心板在竖向荷载作用下的开裂荷载、极限荷载及位移和应力分布规律；还对单跨无梁楼盖进行了材料非线性有限元计算，通过分析主应力场明确了柱上暗扁梁的作用；有限元计算的结果验证了以上的理论分析并得到了一些重要的结论，对改进现浇空心板无梁楼盖的构造措施有重要的参考价值。

On the basis of this, from the view of material selection, mixture grade, cement dose, the usage of additive and maintenance management, some measures are put forward for preventing cement-stabilized subbase from shrinking cracking, and the targets of reducing the crack odds of subbase and the crack widths, or staying subbase from cracking are obtained.

在此基础上，从材料选择、混合料级配、水泥剂量、外加剂的使用、养护管理等角度提出水泥稳定粒料基层收缩裂缝防治措施，达到减少基层收缩开裂几率、减少裂缝宽度或延缓基层开裂的目的。

Laser welding has a number of other welding methods can not match the performance, which is a good thermal joint anti-cracking ability and capacity to cold cracking.

激光焊接具有一些其他焊接方式所不能比拟的性能，这就是接头良好的抗热裂能力和抗冷裂能力。

If the paint has severe cracking, cracking of paint need to be careful tick away, painted putty, for polishing, painting.

如果漆面已经出现严重开裂，需要把开裂的漆面小心剔掉，涂上原子灰，进行打磨后，喷漆。

One of the necessary conditions of the initial cracking due to thermal fatigue is that the material on high temperature side has been deformed compressively and plastically, which is different from the cracking due to common fatigue.

热疲劳裂纹张开的一个必要条件是高温侧材料在升温过程产生压缩塑性变形，这与普通疲劳裂纹不同。

The fatigue cracking in Ni〓Al SC at room temperature is characterized by the stage Ⅰ crystallographic cracking.

在室温下，Ni〓Al单晶体中的疲劳开裂是第一阶段性质的晶体学开裂。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。