查询词典 combustion engineer

Moreover, burn time to also affect the burnable full, combustion time is short hard full combustion.

另外，燃烧时间也影响燃烧的充分性，燃烧时间短就难以充分燃烧。

Changsha 410076, China）Abstract: In order to study the slagging characteristics of boiler carborundum combustion liners during pulverized coal stream combustion, the slag samples of pulverized coal stream combusting experiments were investigated by optics microscope and X-ray diffraction.

摘 要：采用光学显微镜和X射线衍射等方法对煤粉气流燃烧过程在碳化硅质卫燃带上的渣样进行测试，并对渣样的形貌及结晶特性、渣样成分与碳化硅之间的高温烧结特性进行分析。

After taking those factors, such as stable combustion and reducing pollutant emissions into account, the following operation parameters are recommended: combustion temperature between 850℃ and 860℃, excess air coefficient of 1.35, secondary air fraction 40% and mass mixing ratio 30%.

综合考虑稳定燃烧和降低污染物排放等因素，得出一系列最佳燃烧参数。燃烧温度应该控制在850~860℃，过剩空气系数应该控制在1.35左右，二次风率应该控制在40%左右，质量掺混比应该控制在30%左右。

The waste combustion in the waste bed and the impacts of the waste burning efficiency are complex. In order to solve this problem, the method of numerical simulation has been adopted to simulate waste combustion, and calculate the mass loss rate, moisture evaporation, volatile release, char burning rate. Used the total flow rate of primary air between 50～1 000 Nm3/min to calculate the mass loss, excess air coefficient of waste bed, components of the gas. Calculated results show that the burning efficiency is higher when the total flow rate of primary air is at 517.47～632.09 Nm3/min .

针对垃圾焚烧炉床层内垃圾燃烧过程复杂性及影响垃圾燃烧效率因素多的问题，运用数值仿真方法对某垃圾焚烧炉床层垃圾燃烧进行了模拟，获得了垃圾质量流失速率、水分蒸发速率、挥发分释放速率、焦炭燃烧速率和烟气的温度；并在50～1 000 Nm3/min范围内改变一次风流量，获得了床层质量流失比值、过剩空气系数和烟气中各组分的质量百分比含量。

Combustion parameters such as ignition temperature, peak temperature of maximum weight loss rate, burnout temperature, maximum rate of combustion, and combustibility index were analyzed.

分析了燃烧特征参数如着火温度、燃烧速率最大时的温度、燃尽温度和最大燃烧速率以及燃烧特性指数。采用Freeman-carroll法计算了燃烧动力学参数。

The effects of combustion chamber shape and start of injection on mixture preparation and combustion were analyzed.

分析了燃烧室和喷油始点对预混合气形成及燃烧的影响。

In other words, the results novelty broke the conclusion in the pervious reports that combustion synthesis can't occur once Fe content in Fe-Ti-C system is more than 60wt%, and gave more engineering meaning to combustion synthesis of iron-based composites.

而这正是本研究的创新点之一，即打破了前人研究所得出的"Fe-Ti-C体系中Fe含量超过60wt％就不能实现燃烧合成"的界限，从而使Fe-Ti-C体系燃烧合成制各铁基复合材料更具有工程意义。

Combustion process of a ceramic heat insulated compound engine was experimentally studied in a constant-volume combustion bomb and a B1135 type single-cylinder diesel engine.

结果表明，由于陶瓷隅热复合机的压缩终点温度和压力很高，使滞燃期过短，空气粘度高，着火点在喷油嘴孔口附近，初期火焰横贯喷注，使空气与燃油混合条件差，因而仍沿用常规发动机燃烧系统参数时，燃烧过程恶化、燃油消耗率上升。

Ionic current signal was detected in progress of combustion in constant volume combustion chamber on this system.

利用火花塞离子电流法建立了相应的离子电流检测系统。

The strategy and controller are coming from combined analysis of combustion mechanism, generation mechanism of pollutants, influential elements, present application status of PID control method in combustion, as well as sum-up of controlling experience and contradistinctive researches of control strategies. It is shown that this method, when applied to furnace temperature controlling and activated-sludge process, is able to ensure controlling objects tracking in the presence of varying operation conditions, as verified via computer simulation. The thesis consists of chapters as following: Chapter 1 generalizes the research objective and brings forward the inferior theme; generation mechanisms of pollutants

本论文由以下章节组成：第1章对研究课题作了综述，提出了研究的子课题；第2章分析探讨污染物生成机理及二次污染物产生的条件，研究了控制污染的工程控制策略；第3章分析研究了仿人智能控制基本理论及其优越性；第4章通过仿真实验验证了仿人智能控制算法在炉膛温度控制中的有效性；第5章分析研究了有效防止二次污染的烟气处理方法；第6章通过仿真实验验证了仿人智能控制算法在废水生化处理中的可靠性和有效性；第7章总结了全文研究工作并对今后的工作作了展望。

Connectors are lines that can be anchored to particular places, called glue points , on the graphic object.

连接符，可固定在图形对象的特定的地方的线条。

Another way of putting it, too many agents have a say in each other's work, and bureaucratic rigor mortis sets in.

另一种表达是，太多的作用物在彼此的工作里都有话语权，官僚的僵尸开始抬头。