查询词典 circlip

Inside and outside the hand exchange, will install the circlip and the edges and corners return to original state then.

、将内外把手互换，安上卡簧和棱角还原即可。

The inner rotor is eccentrically mounted on a crank, and spring-loaded by a sort of circlip A so that the rotor extremities maintain contact with the inside of the housing, and the volumes of the chambers so created therefore increase and decrease as the crank turns.

内转子是偏心安装在一个曲柄，弹簧加载由一种circlip一，使转子四肢保持联系与内部的房屋，以及大量的分庭，以便创造的，因此增加和减少由于曲柄轮流。

The circlip lead seal packer with sand control is developed for ensuring the normal production of big borehole sand control well.

为保证大井眼防砂井正常生产，研制了卡簧式铅封防砂封隔器。

And then tighten the clamp bench seat belt; transfer, remove with circlip pliers, and then relax circlip pliers-bed NIPs, at which point the attention, the demolition of parts, watch out for spring components, not lost.

然后收紧钳台夹口；阀座内移，用卡簧钳取出卡簧，然后放松钳台夹口，此时注意拆出的部件，留意弹簧组件，不要遗失。

The dissolution of offload valve spool: Using circlip pliers remove the valve core and valve located at the junction of the circlip, and then pipe clamp screwed up spool, remove the inside of the cylinder, valves, O-rings, U-type ring, spring and immersed into the cleaning agent, and then split out the valve on the inlet, the whole body into the soaking, this time, the demolition process by Dutch valve has been completed.

拆减荷阀阀芯：用卡簧钳取下位于阀芯与阀体连接处的卡簧，再用管钳拧出阀芯，取出里面的气缸、阀片、O型圈、U型圈、弹簧并放入清洗剂中浸泡，再拆出阀体上的进气口，将整个阀体放入浸泡，此时，减荷阀的拆卸过程已完成。

Our factory specializes in manufacturing all kinds of springs: compression spring, tension spring, torsion spring, circlip, special-shaped spring; a variety of car parts: Copper, Iron and steel aluminum car parts ; a variety of Chinese Division: Copper, Iron and Stainless Steel Flat Washers, Spring Washers, both inside and outside China Division, E-ring and other hardware.

本厂专业制造各种弹簧：压簧、拉簧、扭簧、卡簧、异型弹簧；各种车件：铜铁不锈钢铝车件；各种华司：铜铁不锈钢平华司、弹簧华司、内外华司、E型扣等五金。

Various kinds of high-quality mineral hydraulic support jack seals and monomer hydraulic support seals, including drum-ring, piston combination ring, Lei-ring, Y-ring, dust ring, piston ring, hoop, O-ring and circlip ring and other kinds of seals.

各类优质矿用液压支架千斤顶用密封圈和单体液压支柱用密封圈，包括鼓形圈、活塞用组合密封圈、蕾形圈、Y形圈、防尘圈、活塞环、卡箍、O形圈及其挡圈等密封产品。

Has analyzed this company new product (after *SR-30, SR-24, SR-20,*SR-16, the SR-13 3/8 series) the production craft, the treating processes and the production efficiency, design a set primarily to include the guide rail, the driving gear, the chain drive, the reduction gear, the electric motor, the shaft coupling, the axis, the bearing, the key, the circlip by V installment and roll spare part and so on drive wheel installments,And completes the correlation selection and the corresponding mechanics examination, with realizes two to need the butt weld the marine riser automatically to, and in the synchro completes the further welding after the spot welding.

分析了该公司新型产品（包括＊SR-30、SR-24、SR-20、＊SR-16、SR-13 3/8系列）的生产工艺、处理过程及生产效率后，设计出一套以V型装置为主包括导轨、驱动轮、链传动、减速器、电动机、联轴器、轴、轴承、键、弹性挡圈及滚动轮等零部件的装置，并完成相关选材及相应的力学校核，用以实现两根需要正对焊接的隔水管自动对中，并在对中点焊后同步转动以完成进一步的焊接。

Core adjusting rolling bearing type 22300 has 2rows of symmetry rolling spherical and copper alloy suppting frame,there is no fixed circlip in inner circle,the roller is the longer type,it has the abillity to support more load,the circlip will lead while moving,it has the better performance of core adjusting,also it can compensate the tolerance of coaxiai degree.

调心滚子轴承22300CA型具有两列对称球面滚子和铜合金实体保持架，内圈无固定挡边，滚子加长，承载能力大，活动中挡圈由内圈引导，调心性能良好，能补尝同轴度误差。

First, according to the model chart ruler, opens cutting the gate hole two, the decision opens the door the direction, changes the slanting tongue direction three, inside and outside the adjustment the hand direction (if: The symmetry holds the hand, does not need to exchange holds about the hand adjustment then), holds the hand like left and right AND gate to open the direction asymmetrically to be opposite, invites you: A, takes down the circlip and the edges and corners with the special-purpose circlip pliers.

一、按样板图尺，开凿门孔二、决定开门方向，改为斜舌方向三、调整内外把手方向（若：对称执手，无需调换执手调整左右即可），非对称执手如左、右与门开启方向相反，请您： A、用专用卡簧钳取下卡簧和棱角。

But in the course of internationalization, they meet with misunderstanding and puzzlement.

许多企业已经意识到了这一点，但在国际化的进程中，仍存在一些误区与困惑。

Inorder toaccomplish this goal as quickly as possible, we'll beteamingup with anexperienced group of modelers, skinners, and animatorswhosenames willbe announced in the coming weeks.

为了尽快实现这个目标，我们在未来数周内将公布与一些有经验的模型、皮肤、动画制作小组合作。