查询词典 bulk density

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Biomass in the rain forest was far more than that in the plantation of 12 years,especially for the shrub layer.But the biomass of litterfall collected in the plantation was greater than that of the rain forest for the reason that Betula alnoidis defoliated in dry seasons.9 Four years observation found that soil bulk density tended to increase first, then decrease after planting trees;total soil porosity and non-capillary porosity tended to decrease and after few years they recovered to different degrees;the soil cation exchange capacity for all forest types increased;in the soil of 0-30cm depth,soil salt saturation tended to decrease;nutrient content in the soil of 0-60cm depth in the young stand tended to decline;soil effective P,effective K and N contents all tended to decrease.

山地雨林的总生物量远远大于10年生的西南桦人工林，其中灌木层的相对差别尤其巨大。94次的观测发现，人工林栽植后，土壤容重一般呈现一个先上升后下降的特点；而土壤非毛管孔隙度、土壤总孔隙度大多呈下降趋势，几年后有不同程度的恢复。

The thermal shock resistance of the brick is expected to improve as a result of bigger bulk density, lower thermal expansion coefficient, phase transformation of fused MgO-ZrO2 eutectic powder, formation of magnesiaalumina spinel and forsterite.

材料性能的变化主要与电熔MgO-ZrO2共晶砂的体积密度大、热膨胀系数小、氧化锆的相变、镁铝尖晶石和镁橄榄石等物相的生成相关。

The kinetic behaviors of ethylene homo- olymerization and ethylene / l-hexene co-polymerization , catalyzed by the metallocene catalyst PS-DVB-MC in an 0.5 L stainless steel reactor , were studied. The effects of polymerization conditions on ethylene polymerization , such as concentration of catalyst , temperature of polymerization , pressure of ethylene , molar ratio of AI / Z r , etc ., were also investigated . Some leading results were as follows : the activity of the catalyst PS–DVB- MC for ethylene homo-polymerization was high ( 1.053 x 107 gPE / mol Zr·h ), but the molar ratio of AI / Zr was low ( 350:1 ); the catalytic ability for ethyleneα-olefin ( such as l hexene etc .) co-olymerization was great , and the corresponding activity come up to a maximum of 1.753 x 107 gPE / mol Zr·h while concenlration of l-hexene was 0.080 mol / L ; the molecular weight of polyethylene was about 180,000 , meanwhile the molecular weight distribution was narrow ( 2.19 ); the bulk density of polyethylene and ethylene / l-hexene co -polymer were 0.25 and 0.34 respectively .

采用0.5L高压不锈钢反应釜，对催化剂PS–DVB-MC催化乙烯均聚和乙烯/ l-己烯共聚合的动力学行为进行了研究，详细考察了催化剂浓度、反应温度、压力、Al/ Zr比、1-己烯浓度等因素对乙烯聚合反应的影响，得到如下主要结论：催化剂PS-DVB-MC具有催化乙烯均聚的高活性(1.053×107g PE / mo1 zr.hr)，低Al / Zr比( 350：1 )；具有良好的催化乙烯与α-烯烃(如1-己烯等)共聚的能力，在1-己烯浓度为0.080 mol / L时，催化活性达到最大(1.783×107 g PE / molZr.hr)；乙烯均聚产物的分子量在18万左右，分子量分布窄( 2.19 )。

Microbial biomass in soil profile showed negative relation with soil pH value and bulk density, while positive correlation with contents of soil organic carbon, light fraction and particulate organic carbon and fine root biomass were found. There were no significant difference between soil microbial biomass and DOC, total N, total P, hydrolyzable N and available P.

土壤微生物生物量垂直分布与土壤pH和容重呈负相关，与土壤的有机碳、轻组有机碳和颗粒有机碳含量及细根生物量呈显著的正相关，但与土壤可溶性有机C和全N、全P、水解性N和速效P含量的相关性不显著。

The results indicated that vegetation biomass had a significant positive relationship with vegetation coverage. They had a significant negative correlation with bulk density of soil, and a positive correlation with macroaggregate, water stability macroaggregate, organic matter content, total nitrogen content, hydrolyzable nitrogen content, available kalium content, microbial biomass, and microbial respiration. However, they had no significant relationship with total phosphorus and available phosphorus.

在其恢复过程中，植被地上生物量与植被覆盖度呈正相关，它们与土壤容重呈负相关，而与土壤大团聚体、水稳性大团聚体、有机质含量、全氮含量、水解氮含量、速效钾含量、微生物量以及土壤呼吸强度之间呈正相关，与土壤全磷、速效磷含量无显著相关性。

Al.were studied in the laboratory,and individua l delta-form crystals of antioxidant1010 with good stability,fast drying speed,hi gh purity,heavy bulk density,good flowability,low volatility was obtained.

文摘：在乙醇、低级醇A和水三元混合溶剂中，通过对抗氧剂1010粗品的重结晶精制研究，制备得到了纯度高、堆密度大、流动性好、挥发份低、质量稳定、干燥速度快的δ－型抗氧剂1010。

The soil water content、available phosphorus、soil bulk density、total porosity、noncapillary porosity、total nitrogen also affected the species diversity.

土壤含水率、有效磷含量、土壤容重、孔隙度和全氮含量也对草本层物种多样性有一定的影响。

After fired at 1600℃, with the increase of zircon addition the bulk density of the samples increases while apparent porosity decreases. When zircon addition is 4%, the strength is the best, and the photomicrograph of the sample exhibits a densely packed microstructure, with larger and better developed grains of periclase and spinel. Meanwhile, the direct bonding of solid phases is reinforced.

在1600℃热处理下，随着w(ZrSiO4)的增加，试样的体积密度增大，显气孔率变小，试样力学强度在w(ZrSiO4)为4%时达到最大值。w(ZrSiO4)为4%的试样整体显微结构致密，固相直接结合程度提高；并且方镁石和尖晶石晶粒的晶粒尺寸粗大，晶粒发育比较完整。

I'm strongly against the death penalty — it's an eye for an eye.

我不赞成死刑——这是以牙还牙的报复行为。

And to get you the support you need, we're enlisting all elements of our national power: our diplomacy and development, our economic might and our moral suasion, so that you and the rest of our military do not bear the burden of our security alone.

并给你们所须的支援，我们正徵召国家所有各种的力量：我们的外交及发展，我们的经济力量与道德劝说，所以你们与其他军人不须要孤独地负起国家安全的责任。