查询词典 bevel gear

By combined calculation with drawing, a design method of tooth profile of rough milling cutter for straight bevel gears is introduced.

介绍了一种计算与作图相结合的直齿锥齿轮粗铣刀齿形设计方法，推导了精确计算公式，详述了计算步骤和计算机作图方法，并给出了设计实例。

These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.

这些驱动器，中央螺旋桨轴通过减少锥齿轮2：1减少。

Never seat or back seat the valve using an air wrench; manually seat and back seat the valves with caution, especially when equipped with bevel gears.

没有阀座或后座的阀门采用气动扳手；手动阀座和后座阀门操作要小心，特别是在配置伞齿轮操作机构后。

Go to the CONTOUR window, located right under the BEVEL AND EMBOSS checkbox, and copy the settings shown in the image bellow.

到轮廓窗口中，位于下锥和emboss 复选框，并复制设置显示在图像贝娄。

Veneer plywood production line Equipment: spindle lathe,dryer,Veneer Bevel surface grinder ,veneer joint press,glue-coating machine,pre-press machine,hot press,longitudinal and transversal saw,up-down woketable,sanding machine,plate turnover,Electrical Transferring Machine.

生产线设备主要有热压机、预压机等，另有旋切机、干燥机、单板斜口磨斜机、单板拼接热压机、涂胶机、予压机、热压机、纵横锯边机、液压升降台、砂光机、翻板机电动板卷运输机等设备配套

After that,the approach is presented,which assure that the spiral bevel gears have the high real contact ratio and the lower sensitivity to error.3 The method of geometrical and mechanical analysis is represented on the tooth edge contact in the gears transmission.

结合加工参数设计的局部综合法、几何接触分析、承载接触分析及应力过程数值仿真，构成了具有反馈的闭环优化设计回路，并形成了相应的软件系统，为设计啮合性能良好、高强度、低噪声的弧齿锥齿轮传动提供了有效的工具。

Then,the first garment computer cutting lathe,the first carton box sample cutting machine,the first garment computer cutting room,the first card paper bevel cutting machine and some other patent series of AOKE.

其后相继推出了中国第一台裁皮机、中国第一台纸箱纸盒电脑打样机、中国第一台服装电脑裁床、中国第一台数控卡纸斜刻机等奥科系列专利产品。

The idea is to use a blast of energy to fry the enemy's computers and telecommunications gear.

电磁脉冲概念是利用能量突然爆发来烧毁敌人的计算机和通信设备。

After that the circular worm gear reducer is designed abase on the principle.

然后按照设计准则和设计理论设计了环面蜗轮蜗杆减速器。

Aiming at the landing gear movement of an aircraft, the velocity motion and accelerated motion model is established.

王希彬1，赵国荣1，姜海勋2，杨晓华3 1。海军航空工程学院控制工程系，山东烟台 264001；2。海军驻北京地区航空军事代表室，北京 100041；3。

It also analyzes the feature and development of semi-finish grinding and finish grinding by roller press.

同时进行了辊压机半终粉磨和终粉磨系统的特点和发展分析。

When I got there, water was dripping slowly from the ceiling and forming a pool on the floor.

当我到那里的时候，水是慢慢地从天花板滴而且形成在地板上的一个池。