查询词典 anodizing

The results show that all aluminum anodizing sludges were slightly neutral to acidic and mainly consist of more than 50% Al2O3; the similar total contents of Cu, Pb, Zn, Ni, Cd, and Cr in the 7 samples were found, namely, the concentrations of Pb, Cd were relatively lower, but that of Cu, Zn, Ni, and Cr were higher; the leaching tests indicate that all the samples were classed as nonhazardous wastes; but each of metals in the sample shows very different leaching behavior, possibly depending on their total contents and the final pH of leachates.

结果表明，铝型材污泥属于中性偏酸性物质，主要由Al2O3组成，含量在50%以上。各试样中Cu、Pb、Zn、Ni、Cd及Cr的总含量的分布趋势基本是一致的，其中Pb、Cd的含量较低，Cu、Zn、Ni及 Cr的含量较高。浸出毒性试验表明铝型材污泥属于非危险废物，但污泥中各重金属的浸出特性又各自不同，可能主要与它们在试样中的总含量和浸出液的最终pH值有关。

Machining process and general information:· General Information – Tooling o Plan to have own engineering group as company expands o Hwasung is subcontracted to do engineering currently o Uses same cutting tools as in Korea facility – all diamond o Regrind tools if can o Hwasung has capability to surface grind, repair dies, and make molds with wire EDM process · General Information – Machining o Boundary samples are used: okay, borderline, not good o Quality room has separate windows for incoming and outgoing parts o New equipment will be coming in from FM LaGrange plant o Each operation has pictures and job instructions for what to check and which gage to use to check part o Parts are manually loaded into machine or pallet, depending on line o Auditor checks parts for verification: after operator checks part, puts in bin, auditor checks part and reloads back on line o Have tool management system o A pokeyoke check is used for orientation prior to loading o Machines are guarded o Mostly have CNC machines o Manual chip collection systems o If automated, have robots with grippers to load/unload parts from pallets o After final inspection, operator visually inspects and loads onto plastic dunnage with the crown up and loads into the washer o Repairs: filing down of burrs or sharp edges after anodizing the crown o Have 2 Excello machines for special machining of the pin bores o 2.7% scrap for gasoline pistons o Cycle time is 18 seconds for gasoline piston o Process – Wash o Spray system o 4 stations: heated wash, wash with degreaser, 2 rinse stations o Uses RO water o Operator blow dries piston and puts on dunnage with crown up o Parts wheeled into coating room o Needs major improvements here o Chemical analysis done for bath in chemical room o Comments/Observations: o Relatively small piston facility, but plans for additional space.

加工工艺和一般信息：·–的一般信息工具 o 有自己的工程集团，随着公司的扩展计划 o Hwasung 是分包做当前工程 o 用途相同的扦插工具，如在韩国设施–所有钻石 o 回收料工具如果可以 o Hwasung 已表面研磨，修复模具，和模具丝电火花加工能力过程·一般信息–加工 o 界限示例用于：好交界，不好 o 质量房间有单独的窗口传入和传出的部件 o 新设备会在来从调频拉格朗日植物 o Each 操作具有图片和工作说明的什么复选，计为使用检查部分 o 部件是手动加载到机器或托盘，取决于行 o 审计检查验证零件：置于 bin，运算符检查部分后，核数师检查部分并重新加载回行上 o 有工具管理系统 o 为 pokeyoke 复选用于在加载之前的定位 o 机被保护 o Mostly 有数控机床 o 手动芯片收集系统 o 自动，如果有与要加载/卸载部分从托盘 grippers 机器人 o 后最终检验，运算符将直观地检查并加载到与塑料衬垫冠了与到洗衣机负荷 o 修复：提交下毛刺或锋利的阳极氧化冠后 o 有 2 Excello 机特别加工的销孔 o 2.7%废料的汽油活塞 o 周期时间是为汽油活塞式 18 秒 o 过程–洗 o 喷射系统 o 4 站：加热洗、与脱脂剂洗、 2 冲洗站 o 使用反渗透水 o 运算符吹干活塞式并将了放冠衬垫 o 部件轮式进涂层房间 o 需要重大改善在这里 o 为在化学的房间里浴做的化学分析 o 注释/结论： o 相对小活塞式设施，但额外的空间的计划。

There are a lot of alloys and many of them respond to anodizing differently.

还有大量的合金，其中许多不同的阳极氧化反应。

This is the most expensive part of anodizing.

这是最昂贵的部分阳极氧化。

You can also sand the anodizing off, but I don't recommend it because its a pain in the ass.

您也可以在沙阳极氧化了，但我不推荐，因为它的一个痛苦的屁股。

The obvious benefit of anodizing is you can add color to aluminum.

在阳极氧化明显的好处是你可以添加颜色铝。

About the only time I use this anymore is to remove anodizing.

关于我唯一一次使用此不再是消除阳极氧化。

Its comprehensive coverage focuses on anodizing for surface protection and decorative effects.

它的广泛报导集中在表面保护和装饰作用的阳极电度。

Hard anodizing power supply is an important part of the equipment to deal with metal surface.

硬质阳极化电源是对金属表面进行处理的装置。

Company specializing in aluminum, aluminum anodizing, coloring, such as surface treatment technology.

公司专业从事铝，铝制品阳极氧化、着色等表面处理技术。

Who? I never heard of him, Paul said, before asking teammate James Posey if he had heard of him.

赛后，科比说，他一直都是一名非常出色的射手，今天他打得很棒。

When I joined the company, I rotated around the different sections.

我加入这个公司时，轮换过几个不同的部门。