查询词典 analysis formula

The research contents mainly include: First, the influence of foundation constraint condition to the temperature stress is analyzed, the temperature stress formula of ultra-long concrete anchor plate is deduced, then the influence of length to structure crack can be gotten from the formula. Second, a breathing method is set up to solve the problem of temperature stress in ultra-long concrete constructions. By setting the sliding floor, a breathing system is built up and the temperature stress reduced distinctly. Third, the effect of prestress technique in the control of temperature stress is analyzed, it is simulated and calculated through FEA to get the right way to apply the prestress. Forth, the delay of temperature field and unsteady conduction is considered, the temperature field of ultra-long concrete structure with later poured band is simulated, then temperature stress distribution after casting the concrete is calculated, finally the effect of later poured band to temperature stress of ultra-long structure is analyzed.

本文的研究内容主要包括：(1)分析了基础约束对超长混凝土结构温度应力的影响，推导了超长混凝土地基板温度应力公式，从而得出长度对结构裂缝的影响；(2)针对超长混凝土裂缝问题，提出了一种可呼吸的解决方法，通过设置滑动层，使结构成为一种"可呼吸"体系，从而有效的降低温度应力；(3)分析了预应力技术在控制超长结构温度应力中的作用，通过有限元模拟计算，得到合理的预应力施加方式；(4)考虑温度场的滞后效应及不稳定传导，对带后浇带超长混凝土结构浇注后的温度场仿真模拟，计算浇注后的温度应力分布，分析后浇带对超长结构温度应力的影响。

Based on the method of minimum deviation angle, man can obtain the accuracy of measuring refractive index of glass at 3×10-6 with fine apparatus for measuring angle, but the classical princip1e formula quoted by these literatures have principle formula error about 4 ×10 - 4 order which lead to an erroneous measure result.

在这些测量折射率的方法中，最重要的是最小偏向用法和V棱镜法。推导最小偏向角法和V棱镜法的所有文献都沿用经典的原理公式，而这些经典的原理公式没有考虑到空气实际折射率对被测试样折射率的影响。

In this paper we have point out the error of principle formula quoted by all literatures at home and abroad to measure the refractive angle and the method of V-prism, derive from beginning the right formula of measuring refractive index by the method of minimum deviation angle and the method of V-prism.

本文指出了测量光学材料折射率的最小偏向角法和V棱镜法国内外所有文献的原理公式误差，重新推导了最小偏向角法和V棱镜法测量折射率的正确公式。基于最小偏向角法用精密测角仅可以获得±3×10-6的折射率的测量精度，然而，这些文献沿用经典的测量原理公式却具有-4×10－4数量级的原理公式误差，因此导致错误的测量结果。

Comparing the improved Taylor formula and other projection angle formulas, the improved Taylor formula correctly reflected the decreasing process of the projection angle to the final value and could describe the projection angle more accurately.

利用数值模拟得到的结果比较了平板驱动几种不同的抛射角公式，改进的泰勒公式准确反映出了抛射角下降并趋于终态的规律，其对平板抛射角的描述更为准确。

The mechanical property testing shows that the seamless PLLA tubes perform excellent radial strength,which indicates that the mechanical properties of biodegradable stents made of these tubes was supposed to be excellent.PLLA and its composites were first used in preparing seamless tubes as antecedency of laser-cut biodegradable coronary stents in china.Finite element analyses of the biodegradable coronary stent model indicate the explorative design basically meets the requirement of reasonable and applicable stents.There is not such kind of research yet in domestic.Optimum laser-cuttting parameters of CO2 laser was cauculated based on experiential formula,within it,biodegradable coronary stents,especially those with complex structure would be manufacutured from seamless tubes quickly by laser microprocessing with high consistency to the design model.The processing efficiency of the CO2 laser demonstrated in experiential formula by us will play an important guiding role in manufacturing biodegradable stents by laser-processing.Our stents that ascribed to laser-cutted,slotted tube stent are proved to be biodegradable, self-expandable and good biocompatible,basically reach the international level on the aspest of manufacturing procedures and design.

研究结果表明：壳聚糖改性材料综合性能优于纯PLLA，更适合于作为可降解冠脉支架的原材料；自主设计的探索性自膨胀管状闭环型可降解冠脉支架的性能符合冠脉设计要求，设计、验证生物可降解冠脉支架模型的研究在国内还未见报道；制备的改性PLLA无缝管的力学性能优越，可通过激光切割获得冠脉支架，这是国内首次采用聚乳酸材料来制备通过激光加工出可降解冠脉支架的无缝管；二氧化碳激光器加工精度能达到加工要求，加工出来的血管支架名义设计与实测值误差小，实现了冠脉支架、尤其是带有复杂外观设计冠脉支架的快速化、规范化加工，对二氧化碳激光器加工聚乳酸材料的效果研究在国内外属于首创，获得的经验公式对日后的深入研究有重要的指导意义；制备的支架为激光切割管状闭环型冠脉支架，支架外观设计、支架加工手段、支架的性能都基本接近国际水平，支架样品符合设计的理念，可以实现自膨胀功能。

Finally discussed the conception of the connatural time and observation time, and take example for atomic clock and pulse laser Doppler speedometer, particular analysed problem of antipathic between 'formula of time slow' and formula of Doppler of light, and try to explained some dark understand about this problem before .

最后从固有时间和观测时间的概念入手，以铯原子钟和激光脉冲多普勒测速仪为例，详细分析了"时慢公式"与光多普勒定律之间的不相容问题，并尝试解释了以前对此问题的一些模糊认识。

Through numerical calculation and comparison with the complete formula,the accuracy of the approximate formula for calculation of reflection coefficient often used in AVA method for gas hydrate is discussed.

通过与完整公式的对比，对AVA常用的反射系数近似计算式的精度进行了讨论，同时分析了地震波速度、泊松比、密度等参数对于BSR反射系数的不同贡献。

They concluded that the derivative-free formula is not exact under the assumed conditions, but it is a very good approximate reconstruction formula.

黄朝志等发现在1993年发表的非圆轨迹不含导数的扇束重建公式推导中的一个错误他们的结论是：在假设的条件下，不含导数的重建公式不是精确的，但是一个很好的近似重建公式。

The result shows that frequency calculated using the finite element modeling is closed with those calculated by formula, which has proved approximate formula has very high accuracy.

研究结果表明：采用有限元建模计算基频，其结果与公式计算结果接近，证明近似公式计算精度高。

In some areas,the liquid limit and plastic limit has approximate lineal relevant formula, expressed formula as like this ω P=a+bω L.

这样用液限就可直接计算塑限，是简捷快速、提高效率的较好方法。

The system can be widely used in belt weighing and batching process control,etc.

介绍了基于智能模糊控制的嵌入式配料系统的设计方法，对模糊PID控制过程和系统调零作了重点的讨论，同时给出了PID控制的程序流程图和系统定长调零子程序。

"I dunno," she answered,"but if you show me aroun', I'll recognize it from the lighthouse just outside the porthole."

"我不知道，"她回答说，"如果你能带我转转，我能认出来的，因为灯塔就在舷窗外。"