英语人>词典>汉英 : 转子的 的英文翻译,例句
转子的 的英文翻译、例句

转子的

基本解释 (translations)
trochanteric  ·  trochanterian

更多网络例句与转子的相关的网络例句 [注:此内容来源于网络,仅供参考]

The most ellipse 4- wing rotor s installed in Banbury mixer are used popularly in the large size of tire factories of China, the working part of rotor is spiral wing body shape and its structure affects the quality of compound and the productivity directly.

我国大型轮胎厂普遍使用的本伯里型密炼机上转子均为椭圆形四棱转子,转子的工作部分螺旋棱体形状及其结构直接影响炼胶质量和生产效率。

150HP-300HP screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that———60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12% kf the efficiency compared to the 4:6 dentate, save power 20%, adopts the Swden SKF bearing.

150HP-300HP)螺杆机转子为德国GHH-RAND联轴式机组,采用第三代非对称齿型为5:6的转子,长径比选择合理,其转子的切线速度仅为30'36m/s,远低于一般空压机60m/s 的切线速度,转子之间保持0.003INCH间隙永不磨损,齿间落差小,故回流损失小,比4:6齿型提高效率10-12%,省电20%,采用瑞典SKF轴承,极大延长了主机的寿命。

Br/br/Adopts the GHH-RAND remarkable mainfrane br/(150HP-300HP) screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12 kf the efficiency compared to the 4:6 dentate, save power 20, adopts the Swden SKF bearing.

采用GHH-RAND卓越主机br/(150HP-300HP)螺杆机转子为德国GHH-RAND联轴式机组,采用第三代非对称齿型为5:6的转子,长径比选择合理,其转子的切线速度仅为3036m/s,远低于一般空压机60m/s 的切线速度,转子之间保持0.003INCH间隙永不磨损,齿间落差小,故回流损失小,比4:6齿型提高效率10-12,省电20,采用瑞典SKF轴承,极大延长了主机的寿命。

The results show that there are many differences in the static characteristics of the rotor in large gap annular flow and that in bearings and seals, and the wall friction coefficient changes circumferentially. The results also show that the wall roughness and the eccentricity ratio have considerable effects on the static characteristics in large gap annular flow.

实例计算结果表明:大间隙环流中转子与以灿承和密封为代表的小间隙环流中转子的静特性有很大同;壁面摩擦系数沿周向变化,同时转子和静子壁面粗糙度以及偏心率对大间隙环流中转子静特性有较大的影响。

The technical characteristics of the invention is that: the rotor end face tooth profile contains four, five or six sections of tooth curves with the circular nature; when it has five sections, addendum circular arcs and dedendum circles are added to the addendum or the dedendum of the rotor; when it has six sections, both the addendum circular arcs and the dedendum circles are added to the addendum and the dedendum of the rotor at the same time, to form four different combination schemes; there are common tangents at the connection points of the two adjacent teeth forming curves, which has a smooth tooth-profile without cusp, a high-wearing feature, a long life of the rotor, a small leakage triangle, and a good sealing property.

本发明的技术特征是:转子端面齿型是包含四段、五段或六段圆弧性质的齿曲线;当为五段时,在转子的齿顶或齿根加上齿顶圆弧或齿根圆弧,当为六段时,在转子的齿顶和齿根同时加上齿顶圆弧和齿根圆弧,形成四种不同的齿型组合方案;相邻的两组成齿曲线的连接点处具有公切线,齿型光滑,没有尖点,耐磨性好,转子的使用寿命长,泄漏三角形小,密封性好。

In chapter 2, based on analysis for the existed methods of torsional vibration measurement, a novel measuring method, parallelling dual-beam laser doppler torsional vibration measurement is first put forward by the author, it not only divides translation and rotation of the rotor, but also can be used to measure torsional vibration of non-cylinder rotor.

本文的第二章在分析现有扭转振动测量方法的基础上,首次提出平行双光束激光多普勒扭转振动测量方法,它不仅解决了转子平动与转动的完全分离,还能测量各种非圆形截面转子的扭转振动;为辨别转子的转动方向,还提出双频激光多普勒测振仪,满足故障诊断对测量启、停转子和转速方向变化转子性能的要求。

The steps include selecting a mould, injecting low temperature hot melt materials, drying the low temperature hot melt material mould, taking out the low temperature hot melt material mould, coating with slurry and sand spraying, drying the sand mould, heating for allowing the low temperature hot melt materials to demould, casting and forming, destroying the sand mould, cutting and processing to obtain the finished product.

取一成型模具:该成型模具包括两个对合的半模,于成型模具内设有一螺旋转子的成型模穴及浇铸道;灌注低温热熔材:于浇铸道灌入熔融的液态低温热熔材,液态低温热熔材即填充于对合的两螺旋转子心轴模穴、及两转子螺旋部半模穴;干燥:液态低温热熔材干燥凝固,形成一具有螺旋转子外型的低温热熔材

The contents of this dissertation are involved in studies on quasi steady-state condition of a slow speed-varying rotor system, gain-scheduling control of a quasi steady-state rotor active balancing system, adaptive control of active balancing for a fast speed-varying rotor with actuator time delay and adaptive control of active balancing for a fast speed-varying rotor with actuator saturation. The rotors to be studied include a Jeffcott rotor, a Jeffcott rotor with anisotropic bearings, a flexible rotor with single collocated balancing plane (actuator plane and measuring plane are almost the same one) and a flexible rotor with multiple collocated balancing planes.

研究的内容涉及慢变速转子的准稳态条件、变速准稳态转子主动平衡系统的增益调度控制、带作动器时迟的快变速转子主动平衡系统的自适应控制与带作动器饱和的快变速转子主动平衡系统的自适应控制,转子类型包括Jeffcott转子、轴承各向异性的Jeffcott转子、单并置平衡平面(作动器和测量平面几乎在同一个平面)的柔性转子和多并置平衡平面的柔性转子。

Under the premise of a rotor system satisfying the quasi steady-state condition, the influencing coefficient method based on the steady-state rotor balancing is extended to single-plane or multiple-plane gain-scheduling control of a rotor with slowly varying speed and all factors affecting the stability of a gain-scheduling control are analyzed. Numerical simulations verify that the gain scheduling control can effectively suppress imbalance-induced vibration of a rotor with slowly varying speed.

在转子系统满足准稳态条件前提下,延伸基于转子稳态平衡的影响系数法到慢变速转子单平面或多平面增益调度控制,分析了影响增益调度控制稳定性的诸因素,以数值模拟证实了增益调度控制能有效地抑制慢变速转子的不平衡振动。

According to the rotor dynamics theory,the vortex mechanism and rule of the rotor are closely related to the collision and friction interaction.

根据转子动力学理论,转子的涡动机理及规律与碰摩作用密切相关,考虑下部钻柱与井壁之间是否发生碰摩作用,应用转子动力学理论建立了2个下部钻柱涡动分析模型,探讨了下部钻柱涡动机理及规律。

更多网络解释与转子的相关的网络解释 [注:此内容来源于网络,仅供参考]

barring hole:盘车孔(电机转子的)

盘车装置 barring gear | 盘车孔(电机转子的) barring hole | 盘车电动机 barring motor

rotor:转子

轴流式压缩机会有许多的叶片,形状类似螺旋桨叶片,但是分为"静子"(stator)与"转子"(rotor)两种. 转子就像螺旋桨一般地旋转,在旋转的过程中将气流向后推,这时气流的压力就会提高,温度也会升高. 静子的功用是将因为转子的作用而产生旋转的气流导引回轴向,

salient pole:凸极

触发线圈配备在发电机转子的外侧,可将转子凸极(Salient Pole)通过时的磁阻变化转换为电信号,然后再以电信号的变化为触发条件实施点火. 点火利用发电机转子旋转储存在电容器中的电力. 通过这种方法起动引擎,发电机便可向电子控制单元供电.

stator:静子

轴流式压缩机会有许多的叶片,形状类似螺旋桨叶片,但是分为"静子"(stator)与"转子"(rotor)两种. 转子就像螺旋桨一般地旋转,在旋转的过程中将气流向后推,这时气流的压力就会提高,温度也会升高. 静子的功用是将因为转子的作用而产生旋转的气流导引回轴向,

bitrochanteric:二转子的

bitregister 位寄存器 | bitrochanteric 二转子的 | bitrochantericdiameter 转子间径

bitrochanteric diameter:转子间径

bitrochanteric 二转子的 | bitrochanteric diameter 转子间径 | bitrope 二点重切面

intertrochanteric crest:转子间嵴

intertrochanteric 粗隆间的 | intertrochanteric crest 转子间嵴 | intertrochanteric diameter 股骨大转子间径,股骨转子间径

subtrochanteric:转子下的

8,转子窝fossa trochanterica | 9,转子下的subtrochanteric | 10,转子综合征rotor syndrome

trochanteric:转子的

trochanterian /转子的/ | trochanteric /转子的/ | trochanterion /转节点/

rotary engine:转子发动机

转子发动机(rotary engine)又称米勒循环发动机,是20世纪50年代出现的一种结构新颖的内燃机,由德国人菲加士.汪克尔(Wankel)博士发明. 与往复式活塞发动机的活塞做直线运动不同,转子发动机采用三角转子的旋转运动来控制燃气压缩和排放,