- 更多网络例句与胶乳相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Through optimizing the process and process conditions,the process and process cotrol parameters were reformed based on the degasification theory of latex,so the degasification effects of PVC latex were improved,the VCM residue contents were reduced,and the drying tail gas could meet the discharging standard.
通过优化工艺条件和工艺过程，依据胶乳脱气的理论，实施工艺流程改造和工艺控制参数的改进，提高了PVC胶乳脱气效果，降低了胶乳中的VCM残留量，确保了干燥尾气中残留VCM含量达到排放标准。
-
In order to find the reasonable methods to control latex migration, factors that had effect on latex migration were studied, including co-binder carboxy methyl cellulose (CMC and starch , properties of latex, type of pigments and ratio of different pigments, coating solids content, coating weight, hot air drying compare to infrared drying and drying temperature.
为了探讨合理的控制胶乳迁移的方法，本文对胶乳迁移的主要影响因素进行了研究，包括辅助胶粘剂羧甲基纤维和淀粉、胶乳的性能、颜料种类和配比、涂料固含量、涂布量、热风和红外两种干燥方式以及干燥温度。
-
The latices were stable ,thixotropic and monodisperse .The particle sizes range from 192 to 94 nm depending on the acrylamide fractions. The Hofmann reactions of these latices were carried out to introduce primary amines on the particle surface.
由于一直以来，丙烯酰胺-苯乙烯的共聚物胶乳只能用于制备两性胶乳，为了得到较高的胺化度，我们对不同单体配比的丙烯酰胺-苯乙烯共聚物胶乳进行Hofmann反应，探讨了丙烯酰胺在单体中所占的比例对Hofmann反应的影响。
-
In this paper, the action mode of NMA in the traditional polyacrylate emulsions was studied by extracting the traditional self-curable PA latex film before curing and comparing the properties of two kinds of model latices A and B. Where model A was prepared according to the traditional self-curable PA latex and the model B was a blend of polyacrylates emulsion and an aqueous solution of poly-NMA. The total proportions of the ingredients were adjusted just the same as of model A. The influences of monomers, the dosages of crosslinking monomer A and emulsifier etc.
文中通过构造&共聚&和共混两个胶乳模型，研究了常规&自交联&PA胶乳中N-羟甲基丙烯酰胺的作用模式；分析讨论低温水性PA胶乳的聚合工艺及影响因素；通过分析胶膜的溶失率、吸水率、力学性质和Tg，及用扫描探针显微镜观察薄膜的微观表面形态和粗糙度的测试，研究水性PA胶乳的成膜性能、稳定性及基本性能；测试并分析胶乳作为涂料印花粘合剂和织物涂层剂的使用性能；通过核壳聚合技术对无甲醛胶乳产品进行性能优化。
-
Through the comparison of property and technics between the SBR/organophilic montmorillonite nanocomposites and SBR/Na-montmorillonite nanocomposites , we chose the SBR/Na-montmorillonite nanocomposites that can be industrialized.
按照丁苯胶乳的生产工艺，将蒙脱土做成溶液状态，在丁苯胶乳生产出来之前加入，这既不影响丁苯胶乳的生产，还简化了工艺流程。
-
In this paper,the agglomeration of polymer butadiene latex being caused by a , B -unsaturated carboxylate latex is studied,the particle diameter of polymer butadiene latex was agglutinated from 170nm~180mn to300nm~330nm..
本文主要研究了用α，β-不饱和羧酸共聚胶乳作附聚剂对PB胶乳进行附聚反应，使聚丁二烯胶乳平均粒径由原来的170nm～180nm附聚到300nm～330nm。
-
The effect of dosage of creaming reagent on creaming time, latex solid content and average particle size was studied, and it was found that the composite latex particle size was too large, and the concentration period was too long, about 15 days.
以海藻酸钠为膏化剂对复合胶乳进行了膏化浓缩，研究了膏化剂用量对膏化时间、胶乳固含量和胶乳粒径的影响，结果表明膏化浓缩胶乳粒径较大，膏化周期较长，一般需半个月左右才能得到实用的浓缩胶乳。
-
The special compound latex products are: carboxylic butyl latex, cement latex, pitch latex, high benzene latex, blanket latex, and white paper latex, etc.
淄博齐龙化工有限公司生产的特种合成胶乳主要有：羧基丁腈胶乳，水泥胶乳、沥青胶乳、高苯胶乳、地毯胶乳以及白版纸胶乳等。
-
The influence of reaction temperature, emulsifier and initiator on the preparation of micro - latexes was discussed with emphasis.
在概述乳液聚合及微乳液聚合特点的基础上，介绍了胶乳剪切分散法和微乳液聚合法制备超微胶乳，重点讨论了反应温度、乳化剂和引发剂对微乳液聚合法制备超微胶乳的影响。
-
The pilot-trial technological recipe and process character of SB polymerization was emphatically analyzed. On the base of the considering of the industrialization of normal SB later product, the constant unit volume power was mainly selected as a rule to scale up the polymerization reactor during the industrialization of SB latex as cement additive.
着重分析了水泥专用丁苯胶乳的中试工艺配方和流程特点，在结合常规丁苯聚合工业放大规律的基础上，提出了采用以相同单位体积功为主的放大准则对水泥专用丁苯胶乳的聚合过程进行了工程放大试验，着重考察了搅拌转速、搅拌桨形式和内冷构件等因素对聚合过程稳定性和成品胶乳性能的影响，并分析讨论了20m3工业聚合釜的传热可行性问题。
- 更多网络解释与胶乳相关的网络解释 [注：此内容来源于网络，仅供参考]
-
chlorobenzene rubber latex：氯苯胶乳
chloroanthracene 氯蒽 | chlorobenzene rubber latex 氯苯胶乳 | chlorobenzene 氯苯
-
chloroprene latex：氯丁二烯胶乳
chloroprene 氯丁二烯 | chloroprene latex 氯丁二烯胶乳 | chloroprene poisoning 氯丁二烯中毒
-
collodion emulsion：火胶乳液
collodion cotton 胶棉 | collodion emulsion 火胶乳液 | collodion wool 胶棉
-
compounded latex：复合胶乳
compound-wound relay 复绕继电器 | compounded latex 复合胶乳 | compounded luboil 复合润滑油
-
compounded latex：填充胶乳, 加填料胶乳
compounded essential oil | 混合香精油 | compounded latex | 填充胶乳, 加填料胶乳 | compounded mix | 复合填料
-
compounded latex：加填料胶乳,填充胶乳
compound-wound relay 复绕继电器 | compounded latex 加填料胶乳,填充胶乳 | compounded lubricating oil 复合润滑油
-
Latex：胶乳
另外,胶乳(latex)是引起接触性皮炎的抗原,胶乳与某些食物存在着交叉过敏,47名胶乳过敏的患者,33人食物过敏原点刺试验阳性,其中17人至少对一种食物出现过临床过敏症状.
-
Latex paint：胶乳漆
latex cement 胶乳结合剂 | latex paint 胶乳漆 | latex thickener 胶乳增稠剂
-
rubber latex：胶乳
b.胶乳(Rubber Latex)是高分子化合物的微粒分散在水中形成的稳定的水乳液体系的总称. 主要分树脂胶乳和橡胶胶乳两大类,也包括固体橡胶溶在有机溶剂中,然后再分散到水系介质中的体系. 胶乳可以看成是固-液分散体系.
-
rubber latex：橡胶胶乳
充气吹胀 inflation | 橡胶胶乳 rubber latex | 胶乳 latex