特性表面

词组短语

characteristic surface

与特性表面相关的网络例句 [注：此内容来源于网络，仅供参考]

In addition, some modifications on several computational methods are also presented. Using LMTO method the electronic structure of several systems are studied, and some results are obtained. They are: The ideal Nb (100) surface has three surface states, the multi-layer relaxed surface has two surface states. The surface energy of the ideal surface is higher than that of the relaxed surface, that means that the multi-layer relaxed surface is more stable than the former one, which supports the LEED results. The mono-layer relaxed Ag (111) surface is the most stable one among several" stable surface models"presented by several researchers. The surface energy of Ag (111) surface is higher than that of surface Ag (001), which supports some experimental results such as different reaction rate at different surface orientations for the same material. The surafce states of Si (111) surface not only locate near the Fermi level, but also in the valence band, which agrees well with Cohen's conclusion. Si (111)-H is an effective model for analysing the surface states and H adsorbed on the back surface is a good method for improving the convincingness of the results obtained on thinner slab models. The surface stability depends on three different kinds of MoSi〓(001) surfaces, the surface with mono-layer Si is the most stable one, and the surface with Mo at the first layer is the most unstable one among them. These are consistant with the Kemoda's experimental results. The valence bands of clean or K adsorbed CdTe (111) surface agrees well with the synchrotron radiation studies. The surface of CdTe (111) consists of four kinds of surface models which show different surface electronic structures and different surface structure stabilities. The conclusion agrees well with Wu's experimental work. The different absorbed alkali metals on the CdTe (111) surface give different adsorption characteristics which have relations not only with the valence electrons, but also with the core ones of the alkali metals. The electonic structures of Si-C alloys are different from that of Si-Ge alloys, and the energy band gaps of Si-C alloys do not increase linearly with Carbon concentration, our conclusion supports Alexander's results, but conflicts with Soref's one.

现分述如下： LMTO方法及其应用方面：1）通过对Nb（100）表面电子态分析发现清洁理想表面有三个表面态，多层弛豫表面有两个表面态；表面能大小说明多层弛豫表面更稳定，支持了LEED结果。2）通过对采用不同方法获得的几种不同Ag（111）表面稳定结构的表面能计算分析，给出了单层弛豫表面为Ag（111）表面的最稳定结构；从Ag（111）单层弛豫表面和Ag（001）表面的表面能比较，发现了Ag（001）表面表面能要比Ag（111）小的，表明了同种物质不同表面取向将表现出不同物理、化学性质，这是与实验中得出的结论是吻合的，3）通过对Si（111）表面态分析，不仅发现了Si（111）表面不仅具有居于费米能级附近的悬挂键所对应的表面态，而且还有很多表面态位于价带能量范围内，与Cohen等结果一致，H饱和slab模型背表面相当于增加了slab层的厚度，是一有效的变相增加slab层厚的方法，弛豫表面较清洁理想表面价带谱们低能端的少许移动，预示着总能降低，说明弛豫表面较清洁理想表面稳定。4）MoSi〓具有三种表面，从费米能级上态密度值大小得到单层Si表面最稳定，Mo原子为表层原子的表面最不稳定，双层Si原子表面居中的结论，这与Kemoda等人实验结果是一致的。5）通过对CdTe（111）表面表面电子态、表面结构稳定性及表面H、碱金属吸附的电子结构系列研究，不仅得出了CdTe（111）清洁及碱金属K吸附价带谱与同步辐射光电子谱相吻合的结果，而且发现了CdTe（111）表面具有四类不同原子近邻特征，表现出四类不同的表面结构及电子结构特征：不同表面态分布、不同的表面结构稳定性（表层原子与次层原子成三键有一悬挂键的表面要比表层原子与次层原子成一键有三悬挂键稳定（与Wu等人实验结果一致））、不同的H吸附特性。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

Through the studies on the local geometrical features of Tripod Operator, an approach for 3-D surface discontinuous detection is proposed at first. A Tripod Operator based description approach for free-form 3-D surface is then investigated.

并根据Tripod算子所具有的与模型无关的局部几何特性，提出一种基于Tripod算子的任意型表面整体描述方法，利用Tripod算子提取的局部特征在整个三维表面的统计特性，对三维表面进行更为简洁、准确的整体描述。

The discrete random height variable of worn surface is described with continuous random variables by a mathematical method.

建立了磨损表面轮廓数值化基准、用连续随机变量来描述磨损表面轮廓线高度离散随机变量，对磨损表面高度分布作了数理统计分析，研究了载荷、滑动速度及镀层种类对磨损表面几何特性的影响，将数理统计分析结果与镀层的耐磨性作了比较分析，较为完整、深入地描述了磨损表面的几何特性。

It is very difficult to eliminate these influence factors completely by conventional treatment. Surface properties and surface treatment of ultrafine red phosphorus and MMT and their interface properties with polymer matrices were studied in this thesis. The results were characterized by GC, FTIR, XRD, DTA, TG, XPS, UV, SEM, TEM and other physical and chemical methods. The main contents are as following: 1. The study of factors influencing ultrafine red phosphorus's invariability and phosphine liberation indicated red phosphorus undergone oxidation and dismutation reaction in air, and trace ion of iron, copper and nickel fastened water absorption and oxidation, in which the effect of copper ion was the most, while aluminium and zinc ion could slow down red phosphorus'oxidation, and silver ion had the best effect on red phosphorus moisture absorption. Inhibitors such as aluminium hydroxide, magnesium hydroxide, organic phenol and ferrous potassuim cyanide had a good effect on reducing red phosphorus moisture absorption and restraining phosphine liberation.

本文围绕纳微米材料的表面处理及其在高聚物基体中的应用这一主题，系统地研究了超细红磷和蒙脱土两种常见材料的表面特性、表面处理方法及其与高聚物基体的界面特性，通过气相色谱、红外光谱、X射线衍射、差热、热重、X射线光电子能谱仪、紫外光谱、扫描电镜、透射电镜等现代分析仪器以及其它物理、化学方法对实验结果进行了表征和分析，全文主要内容如下： 1、对影响超细红磷安定性的因素以及磷化氢的缓释研究表明：红磷在空气中发生缓慢氧化、歧化反应，微量的铜、铁、镍等金属离子增加了它的吸水和氧化速度，其中铜离子的作用最为明显，而铝、锌等离子减慢了红磷的氧化速度，银离子对减少红磷的吸湿性效果最好。

The main results of the investigation are as following:(1) Some important criteria for the design of multi-layer structure are acquired: the ratio of the layer thickness to the contact diameter should be controlled to a value about 0.8; increasing the number of the gradient layers and elasticity modulus of the top layer would benefit to the yield strength and the stress status at the interface.（2）By means of molecular dynamics simulations for a indentation and sliding process, it is discovered that dislocations of 45 direction to the surface occur in the surfaces layer, which is correspond to the direction of the plastic flows observed in the macroscopic continuous medium. The irreversible deformation caused by the dislocation and the atom piles at the surface are responsible for the irreversibility of the force response. They are also the main factors for the friction generation. The temperature and the indentation velocity have significant effects on the deformation behaviors of the material of the surface layer. The yield strength would increase obviously if the indentation velocity is greater than 10 m/s.（3）A method to evaluate the fracture toughness of coating by estimating the crack-density functionβof a Wicker''s indentation was proposed. Meanwhile a new surface treatment technology was developed using non-equilibrium plasma.（4）A MD-FE hybrid method and corresponding software was developed to analysis the tribological behaviors for multiplayer system.

研究主要内容和结果有：（1）得到指导梯度膜设计的几个准则：控制膜层厚度与接触半径比在0.8左右为宜；适当增加梯度层层数和顶层弹性模量，有利于提高抗屈服能力和改善界面处的应力状态；（2）通过对嵌入和滑动摩擦过程的分子动力学模拟，发现表层产生一个与宏观连续介质的塑性流动方向观测一致的45 方向位错；位错造成的不可逆变形和表面的原子堆积，是力的响应不可逆性的原因，也是构成摩擦力的主要因素；温度和嵌入速度对材料变形特性有显著的影响，当嵌入速度大于10 m/s时，屈服强度明显增加；（3）提出压痕裂纹密度系数β半定量判定膜层断裂韧性的方法；并开发出表面强化新工艺；（4）开发出分析表面摩擦学特性的MD-FE复合模拟方法和相应模拟软件。

In this work,atomic force microscopy,near-field scanning optical microscopy,laser scanning confocal microscopy and quantum dot labeling were used to investigate the biophysical properties(the parameters including morphology,membrane nanostructures,membrane pore, friction distribution,adhesion properties,specific interaction of antigen-antibody,distribution mode of membrane receptors and so on) of T lymphocytes stimulated by phorbol dibutyrate plus ionomycin at nanoscale.

本论文基于AFM和NSOM，结合量子点标记及激光共聚焦等技术，以人外周血T淋巴细胞为研究对象，在纳米尺度研究了活化前后以及不同活化阶段T细胞生物物理特性的变化，即细胞形态结构、膜表面纳米结构、膜孔变化、膜表面摩擦力分布、膜表面粘附特性、抗原-抗体间特异性相互作用力、膜表面受体分子分布模式等。

Degradation test in vitro was carried out in phosphate buffer solution (0.1M, pH7. 4) at 37 ℃. The buffer solution was changed daily. Degradation test in vivo was implanted the sample to subdermal in adult ICH rat in the scapular area lateral to the dorsal midline. At suitable time the samples were recovered. Molecular weight changes in surface layer and bulk of polymer sample were measured by GPC and weight loss was determined gravimetrically. It was found that the degradation behavior can be regulated by changing the composition of copolymers. The critical compositions from surface to bulk degradation behavior for PGCA, PLCA, PLMCA, PLDCA systems were 15-20, 20-30, 30- 40, 40 of mol percent GA or LA unit in copolymers, respectively. The degradation behavior of PGCA, PLCA, PLMCA, PLDCA systems were compared and analysed. Some factors influencing the degradation character, such as copolymer composition, hydrophobicity, crystallinity and enzyme affect etc. played important role.

体外实验中材料降解环境为37℃，0.1M，pH7.4磷酸缓冲溶液，每天换液，定期取样；体内实验中将聚合物试样埋置于ICH小白鼠背部肩胛骨皮下部位，定期处死小鼠，取样，将体内体外样品进行重量损失及试样内外层分子量变化测定，分析各聚合物试样降解行为特性，实验结果证明，改变共聚物组成，可以调节各聚合体系降解行为特性，对PGCA，PLCA，PLMCA，PLDCA共聚体系，交酯摩尔百分含量15-20％，20-30％，30-40％，40％分别为各体系内降解行为特性由表面降解型向本体降解型过渡的临界转折点，交酯含量较低的聚合物不同程度地表现表面降解行为特性，论文对各共聚体系体内外降解行为作了分析对照，例如共聚物组成对材料降解速度与降解行为的影响；生物体内酶对降解行为的影响；材料亲疏水性，聚合物链段结晶行为及碳酸酯结构对材料降解行为的影响等，得出交酯/环碳酸酯共聚体系降解行为一些共性和规律。

Through designing of composition and structure of the bioactive graded coating,innerstress and its distribution in the coating were analyzed and calculated, the resultsshowed that when composition distribution coefficient n was 1.5, a reasonable stressdistribution could be got, that was at the beginning of deposition the suspension containingrichly BG granules was used so that a rich BG granules layer, a good transitional layerbetween BG layer at the bottom and the coating could be obtained at the titanium alloy side,the bottom of the coating; the stress value near the interface and surface and its character,pressure stress or tensile stress, were decided by the character of its composition itself.Changing composition distribution coefficient n could only change the variation tendency ofstress in the coating, but did not change the stress distribution rule in the coating. Thethinner the coating is, the sharper stress variation in the coating is, which does not mean thatthicker coating is better because the thicker the coating is, the little the permitteddeformation of coating is, so the coating thickness should be thinner, for example, about50μm for bending applications, but for applications only bearing pure shear stress, such asroot of tooth implant, the coating can be thicker little, for instance, about 80～100μm. The study on electrification characteristic and electrophoresis deposition of HAand BG granules in aqueous and non-aqueous solution system found that EPD almost didn'toccur in aqueous solution system. However, because HA granules take position charges inabsolute alcohol, a homogeneous EPD be carried out on the cathode titanium alloy slice, but taking negative charge in absolute alcohol the BG granules not be deposited on the cathode. A guided HA crystallizing, 100～300nm, on surface of the BG granules be realized by metathetical reaction, which cover BG granules with HA microcrystals and make the covered BG granules taking position charges in absolute alcohol, sequentially realize the EPCD of the BG and HA granules on the cathode, so it is feasible to make a titanium alloy/BG/HA bioactive graded coating by making use of EPCD technology. The corrosion experiment of rich boron bioglass coating and plasma spray coating showed that split phase, rich boron and rich silicon phase, occurred during its preparation. In basic medium the corrosion behavior of 〓 BG coating showed uniformity corrosion, the corrosion mostly occurred at rich boron phase area, therefore batch formula design of BGshould avoid the occurring of split phase. The corrosion appearance of plasma spray coatingappeared a non-uniform corrosion, mostly occurred at the edge of the laminated HA moltendrops, and emerged an accelerated corrosion tendency, which will easyly lead to corrosioncrackles extending to the interface and the happening of osmotic interfacial corrosion, thatmay be one of the major reasons leading to the coating cracking-off in the later period. Thetesting results of thermal expansion coefficient of 〓 and 〓BG showed the thermalexpansion coefficient of 〓 BG matched with that of titanium alloy better, and 〓 BG couldsinter with titanium alloy into densification enamel layer at low temperature (720℃).

将Ti6Al4V合金在1000℃下进行真空热处理会降低其力学性能，且合金内的V元素会向表面富集，因此，钛合金真空热处理和表面涂层的烧结温度不能过高，即应低于其相转变点；通过对生物活性梯度涂层的组成和结构的设计，分析和计算了梯度涂层内的应力大小和分布，结果表明：对于本研究，当成分分布系数n=1.5时，可以获得较合理的涂层力学性能，即在沉积开始时，采用富含BG颗粒的悬浮液，以便在钛合金侧获得同底层BG有良好过渡的富BG涂层；梯度涂层界面和表面的应力大小、性质由材料组成本身的性质决定，改变成分分布系数，只能改变涂层内应力变化的趋势；涂层的厚薄不影响涂层内的应力分布规律，但涂层越薄，涂层内的应力变化越快，但这并不意味着涂层越厚越好，因为涂层越厚，涂层允许的变形越小，对于应用于弯曲受力部位的涂层而言，涂层应薄一点为好(50μm)；而对于仅纯受剪切应力的部位，如牙根种植体，涂层可适当加厚(80～100μm)；通过对HA和BG颗粒在水溶液体系和非水溶液体系中的带电特性和电泳沉积的研究发现，它们在水溶液体系中很难发生电沉积；在无水乙醇溶液中，HA颗粒带正电，可在阴极钛合金片上发生均匀的电泳沉积，而BG颗粒则带负电荷；利用复分解反应法，可以制得100～300nm的HA，通过诱导HA在BG颗粒表面结晶，可对BG颗粒进行表面包覆，获得了被HA包覆的BG颗粒，改变了BG颗粒表面的带电特性，使BG和HA颗粒在无水乙醇中均带上正电荷，从而实现了HA和BG颗粒在阴极上的共沉积。

Two kinds of silicon samples with distinct surface treatment, i. e., one surface was chemically etched and the other was unetched, were used to investigate the characteristics of leakage current and surface flashover of semiconductor under impulse voltage in vacuum. The experimental results showed that the surface conditions of samples affected these characteristics greatly. Before flashover, the Ohmic current was observed for unetched samples and the space charge limited current for etched samples, respectively. Meanwhile both samples showed quite different flashover tracks, and the surface-etched samples displayed a much higher onset voltage of flashover.

对采用和未采用表面化学腐蚀处理的半导体硅在冲击电压下的实验表明（参见 Zhang et al ， Applied Physics Letters， 2002），试品的表面状况对其泄漏电流和沿面闪络特性有着很大的影响：在沿面闪络之前，未经处理试品的泄漏电流表现为 Ohm 性电流，而表面处理过的试品表现为空间电荷限制电流特性；同时两类试品表面的闪络通道也表现出不同的特征，而采用表面化学腐蚀处理可以明显提高其沿面闪络电压。

与特性表面相关的网络解释 [注：此内容来源于网络，仅供参考]

surface characteristic：表面特性

表面性能:workpiece surface characteristic | 表面特性:surface characteristic | 项目特征曲线:Item Characteristic Curve

dip coating：浸涂

我公司根据PC材料的特性,已成功开发了用于PC材料(如:太阳光学镜片,风镜镜片,安全头盔镜片,滑雪镜片,手机镜片,PC薄膜,PC板材)的表面加硬液,采用浸涂(dip coating)法在基材表面镀一层3-4um的加硬层即可使其表面硬度达2-7H.

diffuse reflection：扩散反射

「反射」又可分镜面反射(Specular Reflection)与扩散反射(Diffuse Reflection),主要是由於物体表面特性的差异形成. 光线照射光滑表面物体时,会以同入射角度的方向反射光线. 扩散反射则发生於粗糙表面的物体,光线照射物体后,会以多种角度反射光线.

Directivity：指向特性

可作电脑录音设备使用3) 完美的表面电镀工艺处理技术4) 带抗拉的音频连接线和微型管体一体化设计技术5) 配有结构简便的话筒咪座,方便不同的使用需求,可作网络沟通工具来使用 技术指标[]指向特性(directivity) 单一指向性(un

surface evenness：表面平整度

pavement characteristics 路面特性 | surface evenness 表面平整度 | surface roughness 表面粗糙度

lubrication：润滑

(1)润滑(Lubrication) 用润滑剂减少两摩擦表面之间的摩擦和磨损或其它形式的表面破坏. (2)润滑类型(Types of Lubrication) 润滑剂在两表面间存在的条件和状态. (3)流体润滑(Fluid Lubrication) 作相对运动的两固体表面被具有体积粘度特性的流体润滑剂完全隔开时的润滑状态.

surface tension：表面张

利用喷印技术及胶体表面张 (surface tension) 的物特性来制作微透镜阵列并应用於导光板微结构,达到抑制全反射,增加正向出光效率及均齐度. 透过控制喷印液滴数、基板温度及 UV 硬化胶黏度(10cp及20cp)可改变透镜粒径大小及成型厚度.

touchable characteristics of wood：木材的触觉特性

木材表面性质 surface properties of wood | 木材的触觉特性 touchable characteristics of wood | 木材的视觉特性 visible characteristics of wood

anodizing：阳极处理

锡 Sn 以防止汽缸 回目录 1.3 表面处理之重要性 表面处理工业虽然不是工业之主流,但只有透过表面处理, 表面处理工业虽然不是工业之主流,但只有透过表面处理,制品的特性及价值才能充份发挥 出来.应用电镀(plating),阳极处理(anodizing),化成处理(convesion coating),

surface pressure-area isotherms：表面压力-面积等温线

surface potential 表面位 | surface pressure-area isotherms 表面压力-面积等温线 | surface properties 表面特性