- 更多网络例句与润滑脂枪相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Bearings run in the 48 hours after the grease gun to use to stamp bearing the pressure to add oil into the grease cup.
在轴承运行48个小时后，要用润滑脂枪向轴承盖上的压注油杯注入补充润滑脂。
-
Lubrication method for linear rail system are divided into grease gun and pump.
直线导轨系统的润滑方法有专用给脂枪和泵。
-
Use arm lubricating gun to inject grease to the lubricating position of beam pumper with large work intension and long well off, which effects oil production efficiency seriously, is easy to well recline for sandy well and causes waste .
中文摘要：使用压杆式黄油枪把润滑脂注入到游梁式抽油机润滑部位，工人劳动强度大，停井时间过长，严重影响了采油时率，对于易出砂井，还容易躺井，造成了作业费用的浪费。
-
Using the Grease Gun to fill in th e heat-resistant lubricating grease, then fasten the bolt and close the door.
打开侧门，旋下注油螺钉，用黄油枪加满耐高温润滑脂，旋紧螺钉，装上侧门
-
If not, the bearings will be worn and the life will be shortened, The methods of maintenance are as follows: oiling once for each shift. It should be noticed that the oil channel must be cleaned immediately if the oil is not be consumed or the loss is slow then 50# motor oil should be added. The oil cup is placed on the upper end of principal axis. Each shift should add 3# lithium base grease once with grease gun on bearing of principal axis base and bearing of milling roller. Disconnect and clean the analyzer once for 6 months and apply 3# lithium base grease. Apply lithium base grease for bearing room.(see lubrication system for details).
保养方法如下：主轴加油时间每班一次，但必须注意，发现油杯的油没有损耗或损耗太慢时，应立即清洗油道，再加50#机械油，油杯位置在主轴上端，主轴底座轴承，磨辊轴轴承每一班用黄油枪加注3#锂基润滑脂一次，分析器轴承每六个月拆开清洗一次，加足3#锂基润滑油，风机轴承室加锂基润滑脂。
-
As the most suitable. In the notation of this grease, we should be careful not to melt into the heat, it can not be used to add other lubricating grease in ways to reduce their consistency, the correct way is to inject oil gun, scraper or wipe your fingers into the bearing cavity.
在加注这种润滑脂时，要注意不能加热熔化注入，也不能采用向润滑脂内加其它润滑油的办法来降低其稠度，正确的注入方法是用油枪、刮刀或用手指抹入轴承腔内。
-
Using positioning screw holes and bearing clearance interlinked, first soaked in kerosene inside bearing 1 h ~ 2 h, with a special nozzle and the inhalation of kerosene oil gun repeatedly into bearing 2 or 3 times, pour dry oil lubricating the gun will be required to Fat can be added to.
利用定位螺丝孔与轴承间隙相通，先将轴承浸泡在煤油里1 h～2 h，用特制油嘴及油枪吸入煤油，反复打进轴承2～3次，淋干后用油枪将所需润滑脂加进去即可。
-
Product distributor, the agent products, industrial lubricants industry, special grease, the electronics industry-specific high-temperature reflow oven chain oil, screw oil, products are: TCS 3670-118 , TCS 6220-SR NO.2, TCS6220-SP NO.2, TCS 6220-AP NO.2, TCS 6220-AB N0.2 400G grease, TCS 400G oil gun, TCS 3670-118 high-temperature chain oil, TCS 3670 -- Concentrated high-temperature chain oil (too much product-sum for the Japanese Society of large machinery plant, automobile factory, bearing plant, earmarked for the military factory in the world oil industry row, were the forefront) NSK series lubricants
日本太森社石油化工株式会社产品中国总代理，所代理产品有，各行业工业润滑油，特种润滑脂，电子行业专用回焊炉高温链条油，丝杆专用油，产品有：TCS 3670-118、TCS 6220-SR NO.2 、TCS6220-SP NO.2、TCS 6220-AP NO.2、TCS 6220-AB N0.2 400G油脂、TCS 400G 油枪、TCS 3670-118高温链条油、TCS 3670-浓缩型高温链条油（太森社产品为日本大型机械厂，汽车厂，轴承厂，军工厂指定专用，在世界润滑油行业排、名前列）NSK 系列润滑油
-
Its characteristics:This product works the pressure is big, work the pressure is whole adjustable, 1 time in a row note amount of oil have another, use vivid, operation convenience, is local to add to note lubrication fat to lead an equipments currently, is a hand to move a fat gun currently, single piece grease lubricate device and concentration lubricate the product that the device can\\\'t act for.
其特点：本产品工作压力大，工作压力可调整，一次性连续注油量多，使用灵活，操作方便，是目前国内加注润滑脂的领先设备，是目前个类手动脂枪，单件油脂润滑装置和集中润滑装置不可替代的产品。
- 更多网络解释与润滑脂枪相关的网络解释 [注：此内容来源于网络，仅供参考]
-
grease compounding：润滑脂调制
grease box 黄油盒 | grease compounding 润滑脂调制 | grease compressor 滑脂枪
-
grease cup：滑脂杯
grease 润滑脂 | grease cup 滑脂杯 | grease gun 滑脂枪
-
Grease pump：润滑脂枪,黄油枪
Grease nipple 油脂嘴,黄油嘴 | Grease pump 润滑脂枪,黄油枪 | Greaser 注油器
-
grease nipple：油脂嘴,黄油嘴
Grease lubricator 滑脂润滑器 | Grease nipple 油脂嘴,黄油嘴 | Grease pump 润滑脂枪,黄油枪
-
Greaser：注油器
Grease pump 润滑脂枪,黄油枪 | Greaser 注油器 | Grease seal 滑脂油封
-
green vitriol：绿矾, 青矾, 铁矾
grease nipple 润滑脂注入口, 润脂枪喷嘴 | green vitriol 绿矾, 青矾, 铁矾 | greenhouse effect 温室效应
-
pressure handhole：受压手孔
pressure gun grease 黄油枪用润滑脂 | pressure handhole 受压手孔 | pressure hardness 压印硬度
-
greasing：润滑(过程),加润滑脂(润滑)
greaser 润滑器[工具,工] | greasing 润滑(过程),加润滑脂(润滑) | greasing gun 润滑枪
-
greasing gun：润滑枪
greasing 润滑(过程),加润滑脂(润滑) | greasing gun 润滑枪 | greasing work 润滑作业