槽榫

词组短语

chase mortise

与槽榫相关的网络例句 [注：此内容来源于网络，仅供参考]

The testing and research can provide reference for the design and optimization of woodworking mortise milling cutters.

对木工榫槽铣刀固有频率的测试研究可为木工榫槽铣刀设计与优化提供借鉴。

Firstly, achieving a new low and high cycle noninterfering loading, the high frequency induction local heating, the control of high cycle vibration frequency and amplitude, and the crack propagation real-time detection, an experimental system of L-HCCF at elevated temperature is established. Secondly, under two vibration frequency (50Hz and 100Hz), the contrast experiment of light and serious corrosion disc slots is done. It is found that the experimental L-HCCF life of serious corrosion disc is less than that of light's, but its dispersion is larger, and the experimental failure is identical with the service's.

首先，进行大量试验工作，提出了高低周疲劳载荷的新型加载方案，并解决了高频感应局部加温、振动调频及裂纹实时监测等多个技术难点，建立了涡轮盘全尺寸高温复合疲劳试验系统；验证试验做到了故障再现；接着进行了两种频比（振频50HZ与100HZ）的轻、重腐蚀盘的对比试验；由对榫槽第一齿进行裂纹实时跟踪，得出了枞树型榫槽的复合疲劳裂纹扩展特点规律；对榫齿断口进行的金相分析表明：裂纹首先由第一齿开始，断口系复合疲劳；试验结果显示：重腐蚀盘试验寿命较轻腐蚀盘有显著的下降，而且分散性较大。

Machined edges along mortises, dados and /or rabbets will be free of chipping in excess of 0.5mm.

机器修边时，周边的榫槽，榫眼，榫口不可崩缺，接受在0.5mm以内，外露木头要上色一至。

This article mainly is through the analysis aircraft engine on turbine disk key way unique feature, situations and so on processing craft, determined the design proposal, has completed the processing turbine disk key way horizontal-type broaching machine tongs design.

本文主要是通过分析航空发动机上的涡轮盘榫槽的结构特点，加工工艺等情况，确定设计方案，完成了加工涡轮盘榫槽的卧式拉床夹具的设计。

This article mainly is through the analysis aircraft engine on turbine disk key way unique feature, situations and so on processing craft, determined the design proposal, has completed the processing turbine disk key way horizontal-type broaching machine tongs design.

毕业论文字数：28301 页数：64 带图纸任务书说明书）摘要：本文主要是通过分析航空发动机上的涡轮盘榫槽的结构特点，加工工艺等情况，确定设计方案，完成了加工涡轮盘榫槽的卧式拉床夹具的设计。此夹具主。。。

This article mainly is through the analysis aircraft engine on turbine disk key way unique feature, situations and so on processing craft, determined the design proposal, has completed the processing turbine disk key way horizontal-type broaching machine tongs design.

毕业论文字数：28301 页数：64 带图纸任务书阐明书）摘要：本文重要是通过火析航空发动机上的涡轮盘榫槽的结构特点，加工工艺等情形，断定设计方案，完成了加工涡轮盘榫槽的卧式拉床夹具的设计。

This article mainly is through the analysis aircraft engine on turbine disk key way unique feature, situations and so on processing craft, determined the design proposal, has completed the processing turbine disk key way horizontal-type broaching machine tongs design.

毕业论文字数：28301 页数：64 带图纸任务书说明书）摘要：本文主要是通过分析航空发动机上的涡轮盘榫槽的结构特点，加工工艺等情况，确定设计方案，完成了加工涡轮盘榫槽的卧式拉床夹具的设计。

Dowel holes and/or mortise notches will have 90%-100% glue coverage on the interior side surface.

榫孔及榫槽内表面要90%-100%布胶。

Companies pay attention to the construction of talent, has a group of senior professional and technical personnel in order to enrich the experience and advanced technology, developed countries new patent products - love Rui Site groove joints Positive Lock assembled solid wood floor.

公司注重人才的建设，拥有一批高级专业技术人才，以丰富的经验和先进的技术，研制出国家新型专利产品-爱瑞思特槽榫锁扣拼装实木地板。

The results of conversion show that the serious disc must be rejected because its reliable L-HCCF life is greatly less than an overhaul period. Finally, the load distribution of centrifugal and vibration force on labe is derived. Using two method, load on the crack labe gradually reducing and keeping constant with the crack propagation, a crack propagation analysis of fir-tree slot is carried out, and the calculating L-HCCF crack propagation life of slot on the unload method, which is nearly 3 times longer than that on constant method, is 20 times shorter than the pure low cycle life, and agree well with the experimental's.

最后，分析了离心力载荷和振动载荷在榫齿上的分布，进行了榫槽榫齿的有限元计算；提出了枞树型榫槽的卸载概念，并按带裂纹榫齿上的承载随裂纹增长而逐步减少和始终保持不变两种处理方法，进行了复合疲劳裂纹扩展及其寿命计算，由计算得出卸载下复合疲劳裂纹扩展寿命较单纯低周疲劳寿命下降二十多倍；按卸载处理的疲劳裂纹扩展寿命是按恒载处理的三倍多，前者与试验吻合，而后者则偏差较大。

与槽榫相关的网络解释 [注：此内容来源于网络，仅供参考]

barefaced tongue and groove joint：楔槽榫

楔;劈尖 wedge | 楔槽榫 barefaced tongue and groove joint | 楔铁 drift

tonguing cutter：槽榫铣刀

tongued-and-grooved joint 槽榫接合,雌雄榫接合 | tonguing cutter 槽榫铣刀 | tonguing-and-grooving plane 舌刨和槽刨

grooving and tonguing：舌槽榫接

开槽焊接 groove weld | 舌槽榫接 grooving and tonguing | 总吨 gross ton

tongued washer：榫舌垫圈

嵌锻接 tongue weld | 榫舌垫圈 tongued washer | 槽榫机 tonguing and groove machine

tongued and grooved：舌槽榫

tongued and grooved 企口板 | tongued and grooved 舌槽榫 | tongued and grooved 企口板

haling joint：半接榫

半永固法;半永久接合 semi-permanent joining | 半接榫 haling joint | 半闭式槽榫 stopped housing joint

halving joint：半接榫

半永固法;半永久接合 semi-permanent joining | 半接榫 halving joint | 半闭式槽榫 stopped housing joint

chase mortise：槽榫

chase leaks || 检漏, 查漏 | chase mortise || 槽榫 | chase pilot || 护航飞行员

through dovetail joint：賈穿鳩尾榫

threshold 臨界值 ;閾值 | through dovetail joint 賈穿鳩尾榫 | through housing joint 開口式槽榫

lap dovetail：互搭鸠尾榫

横凸榫;横舌榫cross tongue | 互搭鸠尾榫lap dovetail | 滑槽榫接pulley mortise