有研磨作用的

基本解释 (translations)

abrasive

与有研磨作用的相关的网络例句 [注：此内容来源于网络，仅供参考]

First of all, the improving feeding helix can not only get material into the ball mill successfully, but also increase ventilated proportion; Secondly ,making use of all sorts of new scaleboards can reform the working condition of skive substance and raise the material adaptability; Third, separating storehouse board, have not only increased control material to flow, and balanced each storehouse smash the function of ability, but also realize thickness pellet grade role; Grind tail storehouse choose hyperboloid drum liner, in axial and circumference direction have incline curved surface, can not only increase steel ball lateral grade , but also still raise steel forge , steel ball grind efficiency.

进料口螺旋的改进，不仅解决了堵料现象，而且加大了通风面积；各种新型衬板的使用，对研磨体运动状态的调节以及对物料的适应性都有了较大的改善；隔仓板不仅增加了控制料流及平衡各仓粉碎能力的功能，而且可以实现粗细颗粒的分级作用；磨机尾仓选用双曲面衬板，在轴向和圆周方向均有倾斜曲面，不仅能够增加钢球的横向分级，还能提高钢锻、钢球的研磨效率。

Methods The antimicrobial peptide of M. domestica pupa were produced largely by infection and injury, which were isolated and purified by trituration, centrifugalization and column chromatography of AKTA purifier. Then the antimicrobial peptides with anti-Toxoplasma activity were selected by haemacytometry and MTT colorimetric method.

通过损伤加感染的方法诱导家蝇蛹大量表达抗菌肽，然后经过研磨、离心和AKTA purifier层析等步骤，将家蝇蛹抗菌肽进行分离纯化，采用血细胞计数法和MTT比色法筛选对弓形虫速殖子有抑制作用的抗菌肽。

objective to isolate and purify the antimicrobial peptides with anti-toxoplasma gondii activity isolated from the haemlymph of musca domestica larvae.methods the antimicrobial peptides of musca domestica larvae were induced by infection and injury were isolated and purified by trituration,centrifugalization and column chromatography.then the antimicrobial peptides with anti-toxoplasma activity were sieved by mtt colorimetric method and haemacytometry.results it was found that two antimicrobial peptides had anti-toxoplasma activity through resource s cationic column chromatography and superdex g75 gel column chromatography.conclusion the two antimicrobial peptides with anti-toxoplasma activity existing in the haemlymph of musca domestica larvae had different anti-toxoplasma effect.

作者单位：山西医科大学寄生虫教研室，太原 030001；化学生物学与分子工程教育部重点实验室山西大学生物技术研究所目的从家蝇幼虫血淋巴中分离纯化具有抗弓形虫作用的抗菌肽。方法通过损伤加感染的方法诱导家蝇幼虫大量表达抗菌肽，然后经过研磨、离心和层析等过程，将家蝇幼虫抗菌肽进行分离纯化，采用四甲基偶氮噻唑蓝比色法和血细胞计数法筛选对弓形虫速殖子有抑制作用的抗菌肽。结果经resource s阳离子柱和superdex g75凝胶柱层析后，筛选出2种对弓形虫速殖子有杀伤作用的抗菌肽。结论家蝇幼虫血淋巴中存在抗弓形虫作用的抗菌肽，而且不止一种，但其效果有所不同。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Be living in the deep well ultradeep well prospecting process ,Since radial direction force 、Eddy is stird 、Elements such as horizontal vibration and so on being ,In the wake of well drilling time the increase ,The auger post writings is used the casing inside wall crossrange strenuously to broaden ,It is more and more grave to cause casing and drilling rig to join the wornout problem .

论文摘要：在深井超深井勘探过程中，由于径向力、涡动、横向振动等因素的存在，随着钻井时间的增长，钻柱作用于套管内壁的侧向力增大，导致套管和钻具接头磨损的问题越来越严重。造成钻具耐磨带失效的主要原因有地层研磨性、钻杆的井下工况、耐磨材料选择与

与有研磨作用的相关的网络解释 [注：此内容来源于网络，仅供参考]

abrasive：研磨剂

牙膏中主要具清洁作用的,并非会产生泡沫的接口活性剂,而是所谓的研磨剂(abrasive). 常见的有碳酸钙、碳酸镁、氢氧化铝、二氧化钛...等. 研磨剂之主要功用,即在除去附着于珐琅质上之牙斑,只要牙斑经常性的去除,珐琅质中被酸作用掉的钙磷,

bending：弯曲力

粉碎过程常用的外加力有:冲击力(impact)、压缩力(compression)、剪切力(cutting)、弯曲力(bending)、研磨力(rubbing)等,参见图4-6. 被处理物料的性质、粉碎程度不同,所需施加的外力也有所不同. 冲击、压碎和研磨作用对脆性物质有效,