有一定结构地

基本解释 (translations)

architecturally

与有一定结构地相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that increasing the solids loading of slurry up to 45% allows minimizing deformation of green sheets during drying and sintering process effectively. When the content of monomers in shurry is 2%-4%, and the content of plasticizer in shurry is 3%-6%, green sheets with good strength and flexibility are obtained. The microstructures and the electric characteristics of PTCR chip thermistors were investigated. A five-layer chip PTCR thermistor with room resistance of 0.8Ω, temperature coefficient of resistance of 13.40%/℃, and ratio of maximum to minimum of resistance larger than 10^5 is successfully fabricated.

研究表明：浆料固相体积分数对坯体的乾燥及烧结行为有较大影响，当浆料固相体积分数在45%以上时，可有效避免制品乾燥和烧结过程中收缩过大而产生的变形开裂缺陷；当有机单体的质量分数为2%~4%，丙三醇的体积分数为3%~6%时，可获得有一定强度和柔韧性的生坯；研究了注凝成型PTCR陶瓷的微观结构及陶瓷元件的PTCR性能，成功地制备了层数为5、室温电阻为0.8Ω、电阻温度系数为13.40%/℃、升阻比大於10^5的多层片式PTCR元件。

The results show that increasing the solids loading of slurry up to 45% allows minimizing deformation of green sheets during drying and sintering process effectively. When the content of monomers in shurry is 2%-4%, and the content of plasticizer in shurry is 3%-6%, green sheets with good strength and flexibility are obtained. The microstructures and the electric characteristics of PTCR chip thermistors were investigated. A five-layer chip PTCR thermistor with room resistance of 0.8 Ω, temperature coefficient of resistance of 13.40%/℃, and ratio of maximum to minimum of resistance larger than 105 is successfully fabricated.

研究表明：浆料固相体积分数对坯体的干燥及烧结行为有较大影响，当浆料固相体积分数在45%以上时，可有效避免制品干燥和烧结过程中收缩过大而产生的变形开裂缺陷；当有机单体的质量分数为2％~4%，丙三醇的体积分数为3％~6%时，可获得有一定强度和柔韧性的生坯；研究了注凝成型PTCR陶瓷的微观结构及陶瓷元件的PTCR性能，成功地制备了层数为5、室温电阻为0.8 Ω、电阻温度系数为13.40%/℃、升阻比大于105的多层片式PTCR元件。

RESULT: 1.Ouabain act on lens sodium-pump,under the LM,lens anterior capsular membrane discontinuous,epithelium cells clustered,occluding zonule seperated,lens fiber layers fractured.Under the EM,cells totally hollowed,mitochondria swelling,myelin figure appeared.RT-PCR examine the expression condition of αsubunit of sodium pump on mRNA level,α1、α2 and α3-isoform are all decreased.2.Digoxin act on lens sodium-pump,under the LM,lens cell oedema,linkage distructed,extensive exfoliation.Under the EM,plasma appeared little half-transparant hollow region,mitochondria swelling and ridge disappeared. RT-PCR examine,α1、α2 and α3-isoform are all decreased.3.Amphotericin B act on lens sodium-pump,under the LM,lens epithelium cells linked tightly,arranged in-line,lens fiber layers arranged tightly and regularily.Under the EM,abbundant cellular organes,exuberant cells function indicated. RT-PCR examine the expression condition of αsubunit of sodium pump on mRNA level,α1 and α3-isoform are increased significantly,demonstrated isoform-specific action.4D-thyroxine act on lens sodium-pump,under the LM,lens plasmalemma integrated,cells arranged tightly and regularily.Under the EM,nucleus fission appeared,desmosome half-desmosome and tensile microfilaments linked the cells. RT-PCR examine,α2 and α3-isoform are increased, also demonstrated isoform-specific action.5.Vitamin E act on lens sodium-pump,under the LM,lens anterior capsular membrane continuous and smooth,epithelium cells tightly linked,lens fiber layers appearede hollow region occasionally.Under the EM,lateral membrane high density belt appeared,abundant nucleolus. RT-PCR examine,onlyα1-isoform are increased, demonstrated significantly isoform-specific action.6.DMSO act on lens sodium-pump,under the LM,lens anterior capsular membrane slightly thicker,cells linkage partly distructed.Under the EM,plasmalemma denaturation,mitochondria swelling.RT-PCR examine,α1、α2 and α3-isoform are all altered slightly and haven't significant meanning.

结果：1、哇巴因作用于晶状体钠泵后，光镜下晶状体前囊膜断裂、上皮细胞聚积、闭合连接分离、纤维板层裂隙，电镜下全层细胞空泡化、线粒体肿胀出现髓样结构，RT-PCR法检测晶状体钠泵α亚单位α1、α2及α3三种重整异构体在mRNA水平的表达均减弱。2、地高辛作用于晶状体钠泵后，光镜下晶状体细胞水肿、细胞连接破坏、广泛剥离，电镜下胞质见少许半透明空化区、线粒体肿胀嵴消失，RT-PCR法检测晶状体钠泵α亚单位α1、α2及α3三种重整异构体在mRNA水平的表达均减弱。3、两性霉素B作用于晶状体钠泵后，光镜下晶状体上皮细胞紧密连接、线状排列、纤维板层紧密规整，电镜下细胞器丰富、细胞功能旺盛，RT-PCR法检测α1及α3表达显著增强、具有一定的重整异构作用特异性。4、D甲状腺素作用于晶状体钠泵后，光镜下晶状体质膜完整、细胞排列紧密规整，电镜下胞核见分裂像、细胞间有桥粒、半桥粒及张力微丝，RT-PCR法检测α2及α3表达均增强、亦有一定的重整异构作用特异性。5、维生素E作用于晶状体钠泵后，光镜下晶状体前囊膜连续光滑、上皮细胞紧密连接、纤维板层偶见空化，电镜下囊侧膜内有高电子密度带、细胞核仁丰富，RT-PCR法检测仅有α1的表达显著增强、具有极强的重整异构作用特异性。6、二甲基亚砜作用于晶状体钠泵后，光镜下晶状体前囊膜轻度增厚、细胞连接部分破坏，电镜下质膜变性、线粒体肿胀，RT-PCR法检测晶状体钠泵α亚单位α1、α2及α3三种重整异构体在mRNA水平的表达无显著改变。

UDZ Series liquid level indicator of flap disassembly fast and convenient, the installation position can be arbitrary choice, free to change the direction of observation, thus instrumented great visibility; UDZ series of cost-effective liquid level was significantly higher than that used multiple sets of glass plate liquid level of cost performance; UDZ series of liquid level indicator, the sender's device, as well as the liquid level with the main transmission medium within the complete separation of the measured structural design, so that level gauge in the job has pressure (up to 320KG), toxic and inflammable conditions, with absolute safety and reliability; UDZ-3 type uses innovative design, improve the sensitivity of the sensor, and its near-zero drift FarEasTone signals and long-term stability so that it has always been at the scene consistent level instructions; sensors and the main body has a certain interval, which can be solved effectively under high-temperature liquids (up to 480 ) remote detection and control; antifrost type UDZ Series Level Gauge, are I plant the patented product (Patent No.: ZL00221022 3), guarantees that the use of cryogenic liquid level gauge is not freezing (such as liquid CO2), the effective guarantee of the level of a normal job.

UDZ系列液位计的翻板指示器拆装快捷方便，安装方位可任意选择，观察方向可随意改动，因而仪表指示的可视度很大；UDZ系列液位计的性能价格比明显高于采用多组玻璃板式液位计的性能价格比；UDZ系列液位计的指示器，发讯器、以及液位变送均与主体内被测介质完全隔离的结构设计，使液位计工作在有压（可达320KG）、有毒和易燃的工况下，具有绝对的安全性和可靠性；UDZ-3型采用了新颖设计，提高了传感器的灵敏度，其远传信号近乎零温漂和长期稳定性使其始终于现场液位指示保持一致；传感器和主体有一定的间隔，因而能有效地解决高温液体（可达480℃）远距离检测和控制；防霜型UDZ系列液位计，是我厂的专利产品（专利号：ZL00221022·3），保证了在低温液体上使用液位计不结冰（如液体CO2），有效的保证了液位计的正常工作。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Some methods aiming at the two problems have been researched. First, the optimal number of ATE site can be calculated based on a cost model of DAT-ATE. Second, the problem of test schedule which is equitant with two-dimensional Bin-Packing problem is presented. Then a TCG denotation satisfied with T-admissible rule is more convenient for combinational optimization. With Simulated annealing algorithm, better test scheduling results can be achieved; but there is no great optimization space because the efficiency of scheduling is greater than 90%. Third, A novel test compression method——Multi-capture testing is proposed to compress the stimuli. And the ATPG results show that MC achieves high compression ratio which is greater than 90% in some large-scale circuits. MISR, widely used in LBIST, is employed to compress the responses. The aliasing analysis demonstrates that the fault coverage reduction is little due to the existence of aliasing. Fourth, an improved TIC (called S-TIC) aiming at structured test is proposed based on ARM's TIC. A MC scheduling algorithm is proposed to compute the SoC test time and combine MC vectors to SoC test vectors. The scheduling results shows that test time is greatly reduced when using the proper scheduling priority.

首先，给出了低成本ATE的成本模型，根据此模型得到最低测试成本时系统级测试调度的基本参数——测试Site数；其次，本文将DAT-Scan方式的SoC测试调度等价为两维BP问题，为有效地求解该问题，将该BP问题表示为TCG图并通过模拟退火算法解决其求解过于复杂的问题，调度的结果表明该方法在测试时间上有一定改善，并指出DAT-Scan测试调度效率已经大于90％，进一步优化的空间较小；第三，本文尝试通过测试压缩来解决激励所需的测试带宽，提出了Multi-capture结构并解决了MC测试过程中的&矢量&退化问题，MC测试的ATPG结果表明其测试压缩率很高（大电路接近90％）；第四，在激励获得很高压缩比的情况下，测试响应也需压缩，本文采用LBIST中常用的MISR作为MC测试的响应压缩电路，理论分析和实验结果都证明了MC测试的别名对故障覆盖率影响较小（小于2％），并对两类别名的成因做了具体分析；第五，在MC测试及其响应压缩的基础上，本文改进了ARM公司的测试控制器TIC使之适合于MC测试，为了解决MC测试矢量合成问题，本文抽取了MC测试模型，通过固定优先级的MC测试调度模拟将MC矢量合成为ATE矢量，并模拟出了总的MC测试时间。

The flow field construct of meso-β cloud clusters which bring the heavy-hard rainfall in northeast plateau is that the low level cloud cluster is located in the south of converging region, the southern low level influx converged in the cloud cluster and have some affection on the setting up of the rainstorm in the low level. In the middle level, the cloud cluster is lied in near the westerly trough and the southwest airflow ahead of the trough constantly transmits water vapor to the cloud cluster. In the high level, there are a pair of high and low pressure centers around cloud clusters and are obvious divergence airflow, and there is weak ageostrophic high level outflux along pressure force.

产生高原东北部地区大到暴雨天气过程的中—β尺度云团的流场结构特征是：在低层，云团位于辐合区的南部，低层的偏南低空入流在云团内辐合，对大到暴雨的形成有一定的作用；在中层，云团位于西风带低槽附近，槽前的西南气流不断地给云团输送水汽；在高层，云团附近有一对高、低压中心，为明显的辐散气流，沿气压梯度力方向有强度不强的非地转高空出流。

Otherwise, the control of remelting processing parameters of the SiCp/Al composites with a amount of Si in the master matrix, using the kinetics expressions, can be suitably achieved, whereas SiCp/pure Al composites could not.

Ti对SiC/Al界面反应有一定的抑制作用，但不能有效地控制多次重熔过程中SiC/Al间的界面反应，其原因在于局部熔体结构导致的Ti的微观不均匀。

Based on the variation with the structural and geometric parameters for a real engineering, dynamic characteristics for a cable-supported lattice shell is studied with the block Lanczos method by means of the finite element model combined with beam elements, truss elements and cable elements.

选用梁元、杆元和索元的组合有限元模型，采用分块Lanczos法，针对一实际工程，通过改变结构参数、几何参数等诸多因素，较系统地研究了肋环型索承网壳结构的动力特性及抗震、抗风性能，对工程应用有一定参考价值。

与有一定结构地相关的网络解释 [注：此内容来源于网络，仅供参考]

breed：品种

附:品种的定义 品种(Breed):是一个具有较高经济价值和种用价值,又有一定结构和相当数量的动物类群;由于有共同的血统来源和遗传基础,其成员都有相似的特征特性,并能将其重要的特征特性稳定地遗传下去.

Word Formation：构词法

按照语言一定的规律创造新词的方法,叫构词法(Word formation). 从词的形态结构来看,英语单词的构成方式主要有:合成法(Compounding)、转换法(Conversion),派生法(Derivation)和缩略法(Abbreviation). 掌握好构词法不仅有利于同学们顺利地学好英语,

quaternary structure：四级结构

二级结构(secondary structure)是多肽链按照一定方式有规则地旋转或折叠,三级结构(tertiary structure)是在二级结构基础上进一步折叠或卷曲,四级结构(quaternary structure)是含有亚基或亚单位(subunit)的蛋白质亚基与亚基之间的结合方式.

teratogenesis：畸形发生

态的个体.畸形发生(teratogenesis)从形态学来看,畸形是由于形态结构的过度形成和部分正常形成被抑制或缺少以及部位变动而重新组配产生的.联体畸形(二重畸形)尤其在动物是很明显的现象.畸形对某些性态常表现有一定的系统特征.有时可明显地遵从孟德尔遗传定律.另一方面,

compound sentence：并列句

2) 并列句(Compound Sentence)并列句有两个或两个以上的主谓结构. 这些主谓结构之间的关系是并列的、对等的. 从语法上讲,所谓"并列"、"对等"是指任何一个主谓结构都能独立地表达意思,谁也不从属于谁. 尽管如此,这些主谓结构在意思或逻辑上有一定程度的内在联系.