拖板

基本解释 (translations)

planker

词组短语

drag harrow · tool carriage

与拖板相关的网络例句 [注：此内容来源于网络，仅供参考]

The mainly working elements are: crankshaft and clamp are built on the imovable table-board. The headstock has aiguille and it follows dragging board to come true the boring athletics.The landscape orientation of dragging board, the up and down sport of shaking-arm and the running of dragging board turn up the modulating of working station.

其大体工作原理如下：曲轴和夹具安装在固定不动的平台上，装有钻头的主轴箱随进给拖板实现钻削进给运动，工作位置的调整是通过大拖板横向运动、摇臂的上下运动、摇臂的转动来实现的。

Put die on the die seat, adjust cross- plate and transducer draging plate of up and down, so that the steel needle can be inserted into die hole to adjust the pressure of weight, and then place the abrasive, open power switch of ultrasonic and rotating switch of die seat.

模具放在模座上，调节十字脱板及换能器上下拖板，使钢针插入模孔内，调整砝码压力，然后放上磨料，打开超声波电源开关和模座旋转开关。

The main components of the lathe are the headstock and tailstock at the oppoaite ends of a bed,and a tool-post between them which holds the cutting tool.the tool-post stands on a cross-side which enblesit to move sidewards across the saddle or carriage as well as along it,depending on the kind of job it is doing.the ordinary centre lathe can accommodat only one tool at at time on tool-post,but a turret lathe is capable of holding five or more tools on the revolving tueeet.

刀架位于一个纵面板上，小拖板使刀架能够根据加工操作的不同作纵向移动；同时又随大拖板作横向移动。普通顶尖车床只能在刀架上夹持一件刃具，但六角车床可以在其旋转的六角刀架上夹持五件或更多的刃具。车床的床身必须很牢固结实以避免在受力的时候弯曲和变形。请提问的同学最好参观一下工厂的金属切削/机加工车间。那里有车床，还有其他种类的金属切削机床。

Place the die on model base, adjust the cross board and dragging board of transducer to make the steer needle insert into the model pole, then put on abrasive, open up the switch of ultrasonic power and model base circumrotation.

模具放在模座上，调节十字脱板及换能器上下拖板，使钢针插入模孔内，然后放上磨料，打开超声波电源开关和模座旋转开关。

Extension units saddle rack, saddle rack large sliding board to explain in English, Chinese-English dictionary translation results ...

拖板鞍架，大溜板鞍架的英文解释，汉英词典翻译结果。。。。

The transverse bar of the carriage contains ways on which the cross slide is mounted and can be moved by means of a feed screw that is controlled by a small handwheel and a graduated dial.

大拖板上有横向导轨，使横向拖板可以安装在上面，并通过丝杠使其运动，丝杠由一个小手柄和刻度盘控制。

Suitable clutches connect either the rack pinion or the cross-slide screw to provide longitudinal motion of the carriage or transverse motion of cross slide.

合适的离合器或者与小齿轮连接或者与和横拖板的螺杆连接，使拖板纵向移动或使横拖板横向移动。

Regulation by the side of the block-pressed support, so that the supporting block to maintain good contact with the workpiece: by regulating the extension units in the handle, change or reduce the concentration of cutting lathe and extension units in the large gap between the extension units: in order to break them down.

可通过调节上侧支承块的压紧力，使支承块与工件保持良好接触：通过调节中拖板手柄，改变切削浓度或减少车床大拖板和中拖板间的间隙：从而加以消除。

Leadscrew is driven by electric stepping motors. The nut is located on the apron. With the carriage and the knife rest moving, feed comes true.

步进电机驱动丝杠，螺母固定在溜板箱上，带动纵拖板和刀架移动，实现进给运动。

Extension units saddle rack, saddle rack large sliding panels in English translation

拖板鞍架，大溜板鞍架的英文翻译

与拖板相关的网络解释 [注：此内容来源于网络，仅供参考]

chip log：测程板, 拖板计程仪

chip in | 插嘴, 捐助, 下注 | chip log | 测程板, 拖板计程仪 | chip off | 切下

palletize：拖板装扎

拖靶 towing target | 拖板裝紮 palletize | 拖船 tow boat; towing boat; towing vessel; tug; tugboat; tug boat

planker：拖板

plankdrag 木板刮 木板刮路器 木板耢 | planker 拖板 | plankfloor 木板假顶

carriage apron：车床拖板箱

carriage and wagon works || 客货车工厂 | carriage apron || 车床拖板箱 | carriage arbor || 铣刀架

carriage hand wheel：拖板手轮

carriage guideways ==> 托架导板 | carriage hand wheel ==> 拖板手轮 | carriage insurance and freight (CIF) ==> 保险运输费

Cord connector bodies：拖板插座

★Multiple socket-outlets (with cord or pins for power supply connections) 带两对插口以上的插座 | ★Cord connector bodies 拖板插座 | ★Flatiron plugs 熨斗插头

cross slide：横向拖板

cross slide tool box || 横滑板刀具箱 | cross slide || 横向拖板 | cross sliding type || 横移式

portable distribution board：拖板

portable 手提式;轻便的;可移动的 | portable distribution board 拖板 | portable fire extinguisher 手提灭火筒

tool carriage：大刀架,拖板

tool carbide ==> 刀具硬质合金 | tool carriage ==> 大刀架,拖板 | tool carrier ==> 刀架

chip log：测程板, 拖板计程仪

chip in || 插嘴, 捐助, 下注 | chip log || 测程板, 拖板计程仪 | chip off || 切下