- 更多网络例句与压杆相关的网络例句 [注：此内容来源于网络，仅供参考]
-
The formula can be used in approximate calculation of instable critical load of high pier in the design and construction.
本文利用能量原理的Ritz法，在对截面惯性矩变化作线性假定后，推导出变截面空心薄壁高墩失稳临界荷载近似计算公式，可用于设计施工中对高墩失稳临界荷载的近似计算。1中心压杆稳定理论及能量原理中心压杆的失稳问题是稳定问题中的一个最基本的问题。
-
In-plane stability capacity of I-section aluminum alloy bars under eccentric compressions was investigated with FEA program of ANSYS. The stability of the bars with different slenderness ratio and eccentricity was analyzed and the influence of initial crookedness and residual stresses on the stability was emphatically discussed.
动用ANSYS软体对常用的铝合金压型材偏心压杆的平面内稳定承载力进行了研究，分析了不同长细比和偏心率杆件的稳定性能，并讨论了残余应力与初弯曲对杆件承载力的影响。
-
It is pointed out that the members distortional buckling conditions lie on the section firstly and then the length of members.
指出压杆畸变屈曲是否发生首先决定于截面尺寸和形式，其次决定于压杆长度。
-
According to the results, formula on stress expansion range and beam-strut-tie combinated model are deduced, and the method to determine the dimensions of beams and rods are presented.
通过对大量的有限元结果的分析，得出了荷载的应力扩散范围计算公式，提出由梁、拉压杆组成的简化计算模型及梁、拉压杆尺寸确定方法。
-
The principle of minimum potential energy was used to derive the governing differential equation and corresponding boundary conditions.
分析了压杆屈曲时的几何变形条件，导出了压杆的曲率、变形能和各项外力势的表达式，用最小势能原理导出压杆失稳的微分方程和边界条件。
-
Use the cubic function to be the displacement funtion, then base on the energy variation principle, the natural vibration equation is derived, which considers the pressure force and the boundary conditions of the compressed bar.
采用三次函数作为压杆单元的位移函数，基于能量变分原理，构造了一种可以考虑初始内力及边界条件的压杆单元。
-
Researchment on Cable Dome begin with the Concept Design, which including geometric stability, ratio of rise to span, space between struts, height of struts, space between strop, inclination between ridge cable, etc.
对索穹顶结构设计技术的研究首先从概念设计开始，概念设计包括结构的几何稳定性判断、跨度和矢高的关系、压杆的间距、压杆的高度、环索的间距、脊索间夹角等，后面几个部分其实也可以归结为结构几何参数的优化问题。
-
The Levy style Cable Dome model is made up of 〓5 tension piano-wires and 〓32×1 5 compressive steel pipes, distance between nodes and the tension force of cables is adjusted by screw up and down the turnbuckle The procedure of shaping up included four ways, and the loading included fully loaded and half loaded, to validate the influence of unconservative property, the author carried through the slack procedure and the unload procedure.
该Levy型索穹顶模型，以受拉的〓5高强钢丝和〓32×1.5受压钢管构成，节点间拉索的长度以及拉索的预拉力通过拧紧或放松花篮螺丝来调节。试验内容包括成形试验和承载力试验，成形试验尝试了四种不同的成形方法，为了考察结构非保守性的影响，每种成形方法成形后，还逆序进行了结构的松弛试验，荷载态试验包括均布荷载满载（即在所有压杆上部节点施加集中荷载）和半载（在结构1／2的压杆上部节点施加集中荷载）的加载和卸载时结构工作性能的测试。
-
In this thesis, the influence of column force, joint hoop reinforcement, and repeat load on the stress and sheer bearing capability of inclined pressure bar is analyzed utilizing finite element software. In the case study, the column axial force's influence on the inclined pressure bar's equivalent width, stress and sheer bearing capability of RCFEN is obtained by changing the column force when modeling the RCFEN with ANSYS. In the former model, the joint hoop reinforcement influence on the equivalent width inclined pressure bar and the strength of RCFEN is achieved by changing the quantity of joint hoop reinforcement; the inclined pressure bar's equivalent width and the strength variation of RCFEN under cyclic load are gained by applying low frequency cyclic load on the inflection point of column and the middle of beam.
针对上述算例中的框架外节点采用ANSYS进行建模，运用有限元软件分析了柱轴力、节点箍筋、反复荷载对外节点斜压杆承载力、抗剪承载力的影响：改变柱轴力，研究了柱轴力对斜压杆的等效宽度、框架外节点斜压杆承载力、框架外节点斜压杆抗剪承载力的影响；在上述模型中，改变节点箍筋的数量，分析了节点箍筋对斜压杆的等效宽度、框架外节点强度的影响；在上述模型中，在柱反弯点和梁中点均进行低周反复加载，讨论了在反复荷载作用下，框架外节点的斜压杆的等效宽度、框架外节点强度的变化情况。
-
The results show that the most engineering practical columns behave like the interaction of local buckling and overall buckling, and local bucklings of plates do not mean the lost of carrying capacity of overall structures at once.
用本文提出的有限条塑性系数增量初应力法分析了钢偏心压杆局部与整体相关屈曲的极限承载力，得到了中截面的屈曲模式，表明大部分的工程实际的压杆均表现出明显的局部屈曲与整体屈曲的相互作用，板件局部屈曲，并不意味着结构整体立即丧失承载力。
- 更多网络解释与压杆相关的网络解释 [注：此内容来源于网络，仅供参考]
-
strut：压杆
前悬架为压杆(Strut)式,但由于采用了带防震绝缘体的副车架(Subframe),因而提高了整车的行驶平稳性. 后悬架为扭转梁式,更显小型化的特点. 此外,行李箱地板高度的降低,使后悬架得以缩短,突出其短小精悍的特点. 日产的March,
-
strut bar：支撑杆
压杆 strut bar | 支撑杆 strut bar | 扭矩套管 torque tube
-
strut bar：压杆
拉杆 tension rod | 压杆 strut bar | 支撑杆 strut bar
-
bearing cap tighter：轴承盖压杆
bearing calibration 方位标准 | bearing cap tighter 轴承盖压杆 | bearing cap 轴承盖
-
compression member：压杆,受压杆件,受压构件
compression manometer ==> 压缩式压力计 | compression member ==> 压杆,受压杆件,受压构件 | compression mold ==> 压铸模
-
Paper holder bail：压纸杆
滚筒把手Platen knob | 压纸杆Paper holder bail | 压纸释放杆Release lever
-
presser bar lifter：压紧杆扳手
presser bar lifter hinge stud 压紧杆扳手销子 | presser bar lifter 压紧杆扳手 | presser bar spring 押杆簧
-
presser bar spring bracket：压杆导架
presser bar lifter ==> 压紧杆扳手 | presser bar spring bracket ==> 压杆导架 | presser bit ==> 压片
-
presser bar lifter hinge stud：压紧杆扳手销子
pressed tumbler 压机杯 | presser bar lifter hinge stud 压紧杆扳手销子 | presser bar lifter 压紧杆扳手
-
stick relief setting：斗杆安全阀[泄压]调整
stick pivot area;斗杆回转区 | stick relief setting;斗杆安全阀[泄压]调整 | stick rod end relief valve;斗杆缸杆端安全阀