修整用刀

词组短语

beaming knife

与修整用刀相关的网络例句 [注：此内容来源于网络，仅供参考]

The main process machinery and equipment are:(1) hit halo hemp electrical appliances, due to livestock and poultry species, varieties vary;(2) assassination put Xuedao, because different types of livestock and poultry, knives of different sizes, in order to ensure that medical and consumption of blood cleaning hollow knife can be used;(3) peeling or burning hair back hair machinery and equipment, medium and large slaughter plant machinery stripped of pigs, cattle, sheep skin, small factories and individual butcher knife while peeling by hand, Mao 60-68 ℃ hot hot hot flooding 3-8 minutes, easy to back hair, animal hair may be back with a different machine back hair;(4), cut open, cuts except internal organs, cutting off their heads and trimming hooves many different processes such as cutting tools complete with manual and electric saws and a half split two ways , hand-split and a half with machetes, saws chop and a half should be washed clean bone debris.

主要工序机械设备是：（1）击晕麻电器，因畜禽种类、品种不同而异；（2）刺杀放血刀，因畜禽种类不同，刀的大小也不同，为保证医用和食用血液的清洁，可采用空心刀；（3）剥皮或烫毛退毛机械设备，大中型屠宰厂用机器剥去猪、牛、羊的皮，小厂和个体屠户则用手工刀具剥皮，烫毛用60—68℃热水浸烫3—8分钟，便于退毛，畜禽均可用不同的退毛机器退毛；（4）开膛、剖除内脏、割头蹄和修整等工序多用不同的刀具完成，劈半有手工和电锯两种方法，手工劈半用砍刀，电锯劈半后应将骨屑冲洗干净。

It is uese to hold the embedding block for repairing by disposable scalpels.

用于夹持包埋块，以便用修块刀对包埋样品进行修整。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

与修整用刀相关的网络解释 [注：此内容来源于网络，仅供参考]

beamhouse：浸灰间(皮革) 准备车间

beamfilling | 梁间墙 横梁之间的货物 | beamhouse | 浸灰间(皮革) 准备车间 | beaming knife | (肉胴)修整用刀

beaming knife：(肉胴)修整用刀

beamhouse || 浸灰间(皮革) 准备车间 | beaming knife || (肉胴)修整用刀 | beaming || 照耀的, 光亮的, 喜气洋洋的, 愉快的