compressure [kəm'preʒə]

compressure的基本解释

n.

(=compression)压缩, 抑制

与compressure相关的网络例句 [注：此内容来源于网络，仅供参考]

The results show that influence of content of kraft fiber on compressure-resilience and tribology properties was inapparent, however the compressure rate and resilient rate were increased when pressure was increased, and friction coefficient was decreased to some extent when pressure and rotate speed were increased.

在相同比压和转速条件下，纸浆纤维含量对纸基摩擦材料动摩擦系数的影响不明显，但随着比压和转速的增加，纸基摩擦材料的摩擦系数降低，其中含有17.5%纸浆纤维的纸基材料在循环制动条件下的摩擦系数最稳定，磨损率最低。

Five years electrical working experience, know well about compressure air machine,welding machine,hydraulic system ,CNC facilities and power distributions

五年以上电工工作经验，熟悉空压机，电焊机，液压装置，数控加工设备和配电配线

Recovery factor is defined to reflect the recovery effect of air compressure and is measured along the heat transfer surface with different nozzle-to-plate spacing and jet velocity at nozzle exit.

以恢复系数来表示因气体压缩性而引起的恢复效应影响，测量其在传热表面的分布规律以及射流喷射间距和射流出口速度等对恢复系数的综合影响。

The results show that BFRC has favorable impact compressive strength and deformation;,and the impact compressive strength and deformation of BFRC is relational with strain rate and fibre volume content; with strain rate increasing, impact compressure strength and deformation enhance; the impact compressure strength of BFRC is better when the fibre volume content is 0.1%, and the deformation performance of BFRC is better when the fibre volume content is 0.3%.

研究结果表明，BFRC具有良好的冲击压缩强度和变形性能，且其冲击压缩强度和变形与应变率和纤维掺量有关；BFRC的冲击压缩强度和变形随应变率的增大而增加；纤维掺量为0.1%的冲击压缩强度较高，纤维掺量为0.3%时的变形性能较好。

The results show that when the porosity of sample was higher, compressure rate was higher and resilience rate was lower, however resilient rate of sample with higher porosity were increased notably when pressure was increased, and it tended to accord with of sample with lower porosity. The friction coefficient was higher when porosity of paper-based friction material was higher, and the friction coefficient tended to reduce and stabilize when braking pressure was increased. The friction coefficient of sample with high porosity tended to reduce and stabilize in continuous braking cycles.

结果表明：在相同载荷下，随着孔隙率增大，材料的压缩率增加而回弹率降低，随着载荷增加，高孔隙率材料的回弹率先明显增大，而后趋于稳定；在相同比压和转速下，孔隙率越高，材料的摩擦系数越大，随着比压增加，孔隙率高的材料摩擦系数逐渐降低，且不同孔隙率材料的摩擦系数逐渐趋于一致；在连续循环制动时，高孔隙率材料的摩擦系数逐渐降低并趋于稳定。

与compressure相关的网络解释 [注：此内容来源于网络，仅供参考]

compressure：压缩

compressor 压缩物 | compressure 压缩 | comprimario 主要配角

compressure：压缩力

compressor 压缩机 | compressure 压缩力 | comprisal 包含

consolidated drained triaxial compressure：室内土工试验压密排水三轴压缩试验

22. 室内土工试验压密不排水三轴压缩试验consolidated undrained triaxial c... | 22. 室内土工试验压密排水三轴压缩试验consolidated drained triaxial compressure | 23. 原位测试标准贯入试验standard penetration...

consolidated drained triaxial compressure test：室内土工试验压密排水三轴压缩试验

711 22. 室内土工试验 压密不排水三轴压缩试验 consolidated undrained tr... | 712 22. 室内土工试验 压密排水三轴压缩试验 consolidated drained triaxial compressure test | 713 22. 室内土工试验 压密试验 conso...

consolidated drained triaxial compressure test：压密排水三轴压缩试验

压密不排水三轴压缩试验consolidated undrained triaxial compression test | 压密排水三轴压缩试验consolidated drained triaxial compressure test | 压密试验consolidation test