查询词典 visual angle

An eyelike principle for the imaging at monofrequency, monoincidence and small imaging angle is proposed and an interesting complementary relation between the imaging angle and operation wave length for the inverse scattering is revealed.

文中提出在单一波数，单一入射并且小成象角条件下成象的似视原理。揭示了在散射成象问题中存在着成象角与工作波长的互补关系。

Results indicate that when the strain rate is 1200 s-1, the twin number of samples in different orientation increases with plastic strain increasing; when the strain rate increases to 2800 s-1, the σ-ε curves have no obvious charges as the angle is 0o and 45o, compared with that at 1200 s-1; however the σ-ε curves vary from concave to convex when the angle is 90o, because thermal softening has occurred with increasing plastic strain, which results in the number of twin decreasing, and smaller strain hardening

结果表明：当加载应变率为1200 s-1时，不同取样方向的样品中孪晶数量均随塑性变形应变量的增大而增多；当加载应变率增大到为2800 s-1时，取样方向为0°和45°、流变曲线形状较应变率为1200 s-1时没有明显变化，而取样方向为90°时曲线形状由应变率为1200 s-1时的凹形变为凸形，曲线形状变化的原因是由于应变量增大，热软化效应使得孪

We can see that the former research mainly concentrated on creativity, marketing and the brand analysis, most of them were from a subjective angle; and the research from the content analysis angle to make the thorough discussion was so few.

从以往的研究可以看到，关于房地产广告的研究主要集中在对房地产广告个案的创意探讨、营销和品牌的分析，大多是从一种较主观的角度来看问题；而从内容分析的角度对具体的广告内容做深入探讨的研究颇为冷寂，且分析的内容不够全面和细致，变量的设置过于简单。

According to the geometrical principle of conical milling cutter with equal helix angle, a new process of rough machining of conical milling cutter with equal helix angle on universal milling machine by using additive equipment is presented.

根据等螺旋锥铣刀几何原理，提出一种借助附加装置在万能铣床上进行等螺旋角锥铣刀粗加工工艺，介绍了该方法加工锥铣刀时工作铣刀的运动方程；给出了附加装置的设计原理，通过对用此方法加工出的铣刀参数进行测试，证明了这种方法的可行性和实用性。

The horizontal universal milling machine technological transformation based on Mitsubishi PLC;2. Analysis of some important points for makinghelical gear on universal milling machine ;3. According to the geometrical principle of conical milling cutter with equal helix angle, a new process of rough machining of conical milling cutter with equal helix angle on universal milling machine by using additive equipment is presented.

根据等螺旋锥铣刀几何原理，提出一种借助附加装置在万能铣床上进行等螺旋角锥铣刀粗加工工艺，介绍了该方法加工锥铣刀时工作铣刀的运动方程；给出了附加装置的设计原理，通过对用此方法加工出的铣刀参数进行测试，证明了这种方法的可行性和实用性。

The proposed method is based on the formula of rupture plane orientation determined by the aspect ratio of specified silos and involves the effects of the conical angle of the storage surface, so it can deal with two cases: the conical angle of the storage surface and the flat storage surface.

该方法考虑了贮料顶面倾角的影响，可以处理贮料顶面平堆和锥堆2种工况。

The anti-reflux structure includes the stopper (54) having a conically shaped distal surface (59) and the inside surface (32) of the barrel (22) and the distal wall (31) being conically shaped (35) wherein the total included angle A of the inside surface (32) of the barrel (22) at the distal wall (31) is greater than the total included angle B of the distal surface (59) of the stopper (54) by at least 6 DEG .

抗回流装置包括具有圆锥形远面(59)的止动件(54)和针筒(22)在远壁(31)的圆锥形(35)的内表面(32)，其中针筒(22)在远壁(31)的内表面(32)的总夹角A比止动件(54)的远面(59)的总夹角B至少大6°。

It also changes with half corner angle and oil-water contact angle.

还随着角落半角和油水接触角的变化而变化。

The secondary mass flux, Z, cavity convergence/divergent angle, and injection angle have different effect on internal performance of DTN.

二次流量、落压比、凹腔扩张角和收敛角、引射角度都对推力矢量状态下的DTN内流性能有着不同的影响。

To get the steady interface, the ratio of coextrusion flow length to height is at least l-1.5._The role of smooth flow zone is important to reduce the pressure-fall. The higher surface quality of the fluid path can make the velocity field more uniform and the interfacial offset less. However, the layer interface position was almost unaffected by the convergence angle, so for the convenience of die manufacture and extruder\'s collocation, it is fit to make the contact angle as 90°with smooth corner.

在模具结构参数中，共挤出流道的长度和模具壁面光滑程度对界面有重要的影响，根据计算结果得到了方形流道共挤出段长度与高度比的取值范围；而模具入口收敛角对界面的影响不大，在实际生产中为了模具制造和共挤出机布置的方便，可采用圆滑过渡的90°入口角。

Chinese traditional virtue is humility and wariness,the compliment and praise to the others should be declination

中国人的传统美德是谦虚谨慎，对别人的恭维和夸奖应是推辞。如

We bought this house on the never-never.

我们以分期付款的方式买下这座房子。