查询词典 processes

The new method of a simplified processes of fresnel formula for the method of critical angle.

关于临界角法菲涅耳公式简化理论处理的新方法。

The criticality of the processes, and

过程的风险程度，和

The actual processes and practices vary depending on a project's size and criticality or complexity.

实际的开发过程和做法会根据项目的规模和重要性或复杂性而变化。

The recognition of the criticality of these processes has led to the continued development of advanced production and quality assurance systems.

制药公司认识到了这些工艺参数的重要性，持续不断地研究先进的生产和质量保证系统、研究和实施更为苛刻的无菌工艺验证方法。

In addition, the earlier embryogenesis processes of crossbreeding and inbreeding were observed directly by common microscope.

两个交配组合的早期胚胎发育形态基本一致，时间上存在一定的差异。

In contrast to these writings, this essay regards legal reasoning as a crosscutting thinking which can penetrate into all kinds of legal practice and processes of cognition, and put this subject on the core position of the theory of knowledge in philosophy of law.

第三部分即第五章，论述了贯穿于法律推理过程中的四对基本矛盾即：规则和原则，逻辑和经验，确定性和非确定性、真理和价值；分析了它们必然存在的理由、相互作用的过程以及由此所推动的法律推理的发展。

Honing action produces a characteristic criss-cross pattern on a bore known as crosshatch."Edge-broken"phenomenon often occurs at the corners of parts during brittle materials machining processes.

用有限单元法分析了磨粒作用在珩磨轨迹交叉点处的陶瓷材料应力状态，从理论上证明了粗加工中，珩磨轨迹交叉点处陶瓷材料的崩除型去除方式。

But whole technique of production characteristic, is refers to processes in the mold in foundation, moreover auxiliary by other metal crustification, the partial gold-plating, increase the silk tooth to roll technique of production methods and so on character technical process.

而整体生产工艺特点，则是指在模具加工的基础上，另外辅以的其他金属镶嵌、局部镀金、增加丝齿滚字工艺流程等生产工艺手段。

The thesis can be divided into five parts as follows: First, the structural characteristics of finned-pipe evaporator are analyzed. After selecting suitable microelement controller, the heat-transfer and mass-transfer processes are analyzed for every microelement under the conditions of dryness, wetness and frostiness. Based on previous equations, some parameters of frostiness are confirmed and the frost-growing model is set up under frost condition. Some hypotheses are postulated and with the help of the equation of mass-conservation, energy-conservation and momentum-conservation, the evaporation model which fits in the dynamic simulation is built, which set a solid foundation for system simulation. Second, the starting and stopping behaviors under disturbed condition are analyzed and calculated by using the dynamic concentrative parameter model, which gives some advice to better prescribe refrigeration system and set theoretic foundation for carrying out automatic control of refrigeration system. Third, the normal running process is analyzed and calculated by means of rational matching theory, which gives some advice on how to better understand the parameter change under steady state and the affection of inlet-parameter on evaporator. Fourth, the simulation software with dynamic characteristic is designed, which can be applied to calculate thernio-parameter of cryogen, air humidity and frost thickness under different initial and boundary conditions, and to carry out dynamic simulation under conditions of dryness, wetness and frostiness, at the same time, to achieve detection and simulation at any stage from starting to stopping.

本文的主要内容如下：1对翅片管蒸发器结构特点进行分析，选取适当的微元控制体，就干、湿和霜工况下对每个微元分别进行传热传质分析，基于经验关系式确定霜的有关参数，对于霜工况下的霜生长建立模型，经适当假设，运用质量守恒、能量守恒和动量守恒方程建立适合动态仿真的蒸发器数学模型，为系统仿真奠定基础； 2对蒸发在大扰动下的开、停机过程，运用动态集中参数模型进行分析和计算，为更好地描述制冷系统运行的全过程奠定基础，同时也为制冷系统实现自动控制提供一定的理论基础； 3对蒸发器正常运行过程，运用动态分布参数和参数间定量耦合的观点来分析和计算，为更好地了解稳态工况下各点参数的变化情况及各入口参数对蒸发器动态特性的影响即蒸发器性能对各参数变化的敏感性； 4编写翅片管蒸发器动态特性仿真计算程序，可以计算不同边界条件和初始条件下的制冷剂热力参数、空气温湿度和霜厚度分布场，实现对翅片管蒸发器在干、湿和霜工况下的动态仿真。

The fabrication processes for nano-silicon-tips using a (100) single crystal silicon wafer by the anisotropic wet etching in the KOH etchant were designed. Based on the experiment and the model of {411} crystal planes, the crystal planes of silicon tips were analyzed. Through discussing the effect of the mask direction on tip shapes, the process parameters to get high aspect ratio nano-silicon-tips were achieved.

设计了硅尖制备的工艺流程，采用KOH溶液湿法各向异性腐蚀(100)单晶硅的方法制备硅尖，根据实验结果和{411}晶面模型，分析了硅尖侧壁的组成晶面，讨论了掩模偏转方向对硅尖形状的影响，得到了制备高纵横比纳米硅尖的工艺参数。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。