查询词典 defect subspaces

e-PTFE was implanted into the pitting area after subcuntaneous disjunction. Results: 15 cases were followed for about 3 and 6 momths after implant of e-PTFE, including cases with saddle nose, pitting deformity of orbit, congenital lip cleft with depressed soft tissue around pyriform opening, parbial defect of helix. In these cases, satisfaction rate is evaluated as high as 97.9%, unexpected tissue response was not shown in this clinical trail.Conclusion: Depended on this clinical trail, we believe local e-PTFE manufactured by Shanghai Suo-kang Medical Implants Co., Ltd.

由于e-PTFE的组织相容性好，在80年代初期一些发达国家已经应用于整形美容外科[1]，尤其应用于隆鼻术、面部凹陷畸形的整复、唇线增高、唇加厚、鼻唇沟过深的整形美容术、耳廓缺损等手术中，学者们认为e-PTFE排斥反应的发生率低，弹性和硬度与软组织相似，周围组织细胞能够长期进入移植物内，不形成纤维囊，在整形美容外科领域有重要的应用价值。

The causes of female infertility: 1, ovulation disorders: ovarian dysgenesis, luteal phase defect. 2, the endocrine endometrial lack of support, as well as the body of abnormal sex hormone levels or the proportion of non-conforming. 3, reproductive tract obstruction: If intrauterine and vaginal salpingitis of Terrier. 4, for reasons unknown factors and immune factors.

2女性不孕的原因：1、排卵障碍：为卵巢发育不全，黄体功能不全。2、子宫内膜的内分泌支持不足以及体内性激素水平不正常或比例不协调。3、生殖道梗阻：如宫腔及输卵管炎性梗阴。4、原因不明因素和免疫因素。

For the defect of the plated reason, we need control on the polishing step, for the tiny crack, sand hole, material lost and so on we can control on the Casting Step, for the O-ring seal , assembly and process dimension, I can find a good way to solve the issues.

装配过程中出现的密封件配合问题，工艺尺寸设计的合理性等都有有效的解决方案。

Sandie Cox was distraught when told a heart defect could cause her son Lewis to have a cardiac arrest at any minute.

Sandie考克斯心烦意乱时说心脏缺陷可能导致她的儿子刘易斯有一个在任何时间内心脏骤停。

Whatever mutations are, they all lead to defect of dystrophin on sarcolemma.

由于二者病程和功能影响程度不同，正确区分非常必要。

The product poses a risk of scalding as, due to a manufacturing defect, it may burst during use.

通报的理由为该热水袋有制造缺陷，使用时会破裂有烫伤人的危险。

Against the defect of traditional area filling,this paper presents a new method for area filling scan line algorithm.

针对传统区域填充存在的一些欠缺，提出了一种新的区域填充扫描线算法。

The experimental image acquisition system with serial architecture is established, which utilizes area scan CCD sensor. Systematical experiments on defect recognition method have been carried out, and the results show that our method is feasible and valid.

为验证带钢表面缺陷的机器视觉识别方法的有效性，本文建立了基于面阵CCD的串行结构的图像采集和处理实验系统，对缺陷识别方法进行了较为深入的实验研究，结果证明该方法是可行的。

Blade scratch: Paper defect where there is a hair-like indentation in a coated surface running in grain direction.

刮刀痕：顺着纸纹方向，纸面的涂层有着像头发丝的凹痕故障。

Any product can't molding a same thickness. Usually the deeper section may sink mark . To prevent this defect it should set holding pressure, The injection speed of holding pressure step is slow but holding pressure setting within 25-80% depending on sink mark.

任何产品都不同程度的存在一个厚薄不一的问题，正常情况下，较厚的部分都可能存在一个收缩凹陷的现象，为了解决这种现象，就应应用到保压，保压一般来讲都应用较慢的射速，而压力的设置则应看缩水的情况如何，小到25%，大到80%都有可能。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。