查询词典 compensating method

The main works in this paper are as follows:(1). In this thesis, a new method, continuous linearization model, is constructed for the non-linear dynamic systems. The precision Duhamel integration solution for the linearization equation is also given from the theory of linear differential equation. The calculating results show that the new method can improve the calculation precision greatly. In fact, the truncation error is not limited by this method, it can arrive the precision according to the requirement.

本文的主要工作有以下几个方面：(1)由于非线性项的存在，使得多数情况下难以得到非线性动力方程的解析解表达式，目前常使用数值积分方法来求解非线性动力学方程的解，但常规计算方法的计算精度不很理想，本文提出了含Taylor展开项中高阶余项的非线性动力方程的线性化数值计算方法，构造了瞬态线性化方程，给出了Duhamel积分的表达式。

To solve this kind of problem, the dynamic programming method and martingale method are two main method.

目前解决这一问题的主要方法是动态规划方法和鞅方法。

The Information Flow based Buffer method is developed for managing the negative affect of change.And then System Dynamic Modeling method is used to certify the effeteness of the buffer method.

本文开发了基于信息流的缓冲区确定方法用于控制变更所带来的负面影响，并使用系统动力学建模的方法验证了此体系的有效性。

Tuberculosis antigens, Hermans' method to amplify a 245bp sequence of the insertion element IS986 and Eisenach' s method to amplify a 123bp sequence of the insertion element IS6110.among these five methods, Eisenach' s method is the best one, it is specific for M. tuberculosis complex.

发现其中Eisenach的方法具有结核杆菌复合群特异性，敏感性更高，可达10fg DNA，相当于1个结核菌，退火温度为69℃，接近引物延伸温度，便于二步法PCR操作。

At last, the paper has discussed the aggregate technique of discrete method, and analyzed the compute method of cross elastic coefficient and direct elastic coefficient in discrete model, then studied the method used in practice.

最后，本文对非集计模型的集计方法，以及非集计模型交叉弹性系数和直接弹性系数的计算方法进行分析，为非集计模型在实践的应用进行了一些探索。

When the meshless manifold method is utilized to analyze the elastodynamics, the method is divided into the major two parts: the discrete space of the domain is used to the partition of unity, which the present method void to mesh element and refine element.

在求解弹性动力学问题时，弹性动力学积分弱形式的推导采用加权残数法，空间离散采用基于单位分解法的无网格流形方法，时间离散主要采用Newmark法。

The main research contents and results are shown as follows:(1) In order to meet the actural need of this research project, the general ways to bake electrolyzer, which include Aluminium-liquor- baking method, coke-ash-baking method and graphite-powder-baking method, are introduced in details. Their shortcomings and effects on the life-span of electrolyzer are also analyzed.

全文的主要工作和成果总结如下：(1)根据实际科研项目的需要，对现有的预焙电解槽焙烧启动方法铝液焙烧法、焦粉焙烧法和石墨焙烧法进行分析，指出其缺点。

The characteristics of principle, method and practice of discharge survey through broad coil electromagnetic induction method in open full channel are introduced in the paper, and it is compared with supersonic flow survey method in principle and practice.

主要介绍了明渠全渠宽线圈的电磁感应法流量测量的原理、方法、应用特点，并从原理和实际应用等方面，与超声波测流法作了比较。

Due to its good effect in the reservation of information of signal abrupt change, mathematical morphology is often applied in the detection and location of short-term power quality disturbance, however, there is still a defect of invalid detection existing in partial detection methods based on mathematical morphology while some zero-crossing disturbances are detected. In this paper three mathematical morphology based disturbance detection and location methods, i.e., the method based on first-order derivation and morphological gradient, the method based on morphological gradient and soft threshold processing and the method based on dq decomposition and top-hat transform, are analyzed, that is, by means of simulation the adaptability of these methods in the analysis on the signals of voltage sag, voltage swell and electromagnetic transient oscillation is compared.

数学形态学因其在保留信号突变点信息方面有很好的效果，因此常用于短时电能质量扰动的检测和定位，但基于数学形态学的部分方法仍存在对某些过零点扰动检测失效的缺点，文章分析了3种基于数学形态学的扰动检测和定位方法，即基于1阶求导和形态梯度的方法、基于形态梯度和软阈值处理的方法、基于dq分解和高帽变换的方法，通过仿真比较了3种方法在分析电压暂降、电压暂升、电磁暂态振荡等信号方面的适应性，结果发现基于dq分解和高帽变换的方法在检测过零点扰动时具有很好的效果，因此选取这种方法对实测扰动数据进行了检测和定位分析。

This paper mainly studies the feed inlet of explosion pulping equipment which is special in structure. The status of stress distribution was obtained by means of theory analysis method、 finite element method and electrometric method.

本文以压力喷放罐进料口这种特殊结构为研究对象，采用理论分析法、有限单元法和电测法三种方法对其进行了应力分析，得出了进料口的应力分布状况。

"Second Life is remarkably easy to work with, and is very popular,"

"第二次生命是显着容易的工作，并且很受欢迎，"

For example, we usually assume that materials are homogeneous and isotropic and free of internal defects or flaws.

为了得到适合有限元分析的模型，我们必须经过如图2所示的简化步骤。